Exam 5: Conductor Identification, Switch Control of Lighting Circuits, Bondinggrounding of Wiring Devices, Induction Heating

Phase conductors 6 AWG and smaller ____ permitted to be re-identified as equipment ground conductors using green paint, tape, or other effective means.

(Multiple Choice)

4.8/5

(92)

Question 21

The grounded (identified) conductor of 6 AWG or smaller must have an outer finish that is ____.

(Multiple Choice)

4.9/5

(91)

Question 22

Receptacles have several screw terminals for the attachment of circuit conductors. Match the following screws with their intended conductor. -Silver-colored screw

(Multiple Choice)

4.9/5

(82)

Question 23

When terminating a receptacle, the white (grounded) conductor is always connected to the -colored terminal, and the phase (hot) conductor is always connected to the -colored terminal.

(Short Answer)

4.9/5

(82)

Question 24

Match the following switch types with the correct number of terminals for each. -Three-way switch

(Multiple Choice)

4.9/5

(76)

Question 25

In older existing installations, where an equipment ground does not exist in a metal switch box that is located within reach of a conductive floor such as tile or cement, NEC 404.9(B) requires the use of what kind of faceplate?

(Essay)

4.9/5

(69)

Question 26

Specify the maximum overcurrent protection permitted for following the circuit conductor sizes: -12 AWG copper

(Multiple Choice)

4.9/5

(83)

Question 27

Specify the maximum overcurrent protection permitted for following the circuit conductor sizes: -14 AWG copper

(Multiple Choice)

4.9/5

(75)

Question 28

From how many locations does four-way switching allow a lighting outlet to be controlled?

(Essay)

4.9/5

(77)

Question 29

Receptacles have several screw terminals for the attachment of circuit conductors. Match the following screws with their intended conductor. -Green hexagonal screw

(Multiple Choice)

4.9/5

(75)

Question 30

The NEC requires that switching be done only in ____ conductors.

(Multiple Choice)

4.8/5

(83)

Question 31

Showing 21 - 31 of 31

Exam 5: Conductor Identification, Switch Control of Lighting Circuits, Bondinggrounding of Wiring Devices, Induction Heating

Phase conductors 6 AWG and smaller ____ permitted to be re-identified as equipment ground conductors using green paint, tape, or other effective means.

The grounded (identified) conductor of 6 AWG or smaller must have an outer finish that is ____.

Receptacles have several screw terminals for the attachment of circuit conductors. Match the following screws with their intended conductor. -Silver-colored screw

When terminating a receptacle, the white (grounded) conductor is always connected to the ____________________-colored terminal, and the phase (hot) conductor is always connected to the ____________________-colored terminal.

Match the following switch types with the correct number of terminals for each. -Three-way switch

In older existing installations, where an equipment ground does not exist in a metal switch box that is located within reach of a conductive floor such as tile or cement, NEC 404.9(B) requires the use of what kind of faceplate?

Specify the maximum overcurrent protection permitted for following the circuit conductor sizes: -12 AWG copper

Specify the maximum overcurrent protection permitted for following the circuit conductor sizes: -14 AWG copper

From how many locations does four-way switching allow a lighting outlet to be controlled?

Receptacles have several screw terminals for the attachment of circuit conductors. Match the following screws with their intended conductor. -Green hexagonal screw

The NEC requires that switching be done only in ____ conductors.

General Information for Electrical Installations

Electrical Symbols and Outlets

Determining the Required Number of Branch Circuits, Lighting Outlets, Receptacle Outlets

Conductor Sizes and Types, Wiring Methods, Wire Connections, Voltage Drop, Neutral Conductor Sizing for Services

Ground-Fault Circuit Interrupters, Arc-Fault Circuit Interrupters, Surge Protective Devices, Immersion Detection Circuit Interrupters, and Appliance Leakage Current Interrupters

Luminaires, Ballasts, and Lamps

Lighting Branch Circuit for the Front Bedroom

Lighting Branch Circuit for the Master Bedroom

Lighting Branch Circuitbathrooms, Hallway

Lighting Branch Circuit-Front Entry, Porch, Post-Light, Underground Wiring

Lighting Branch Circuit and Small-Appliance Circuits for the Kitchen

Lighting Branch Circuit for the Living Room

Lighting Branch Circuit for the Studybedroom

Dryer Outlet, Lighting and Receptacle Circuits for the Laundry, Powder Room, Rear Entry Hall, and Attic

Branch Circuits for the Garage and Outdoors

Recreation Room

Lighting Branch Circuit, Receptacle Circuits for Workshop

Special-Purpose Outletswater Pump, Water Heater

Special-Purpose Outlets for Ranges, Counter-Mounted Cooking Unit G, and Wall-Mounted Oven F

Special-Purpose Outletsfood Waste Disposer, Dishwasher

Special-Purpose Outlets for the Bathroom Ceiling Heatventlights K J, the Attic Fan L, and the Hydromassage Tub a

Special-Purpose Outletselectric Heating, Air Conditioning

Gas and Oil Central Heating Systems

Television, Telephone, and Low-Voltage Signal Systems

Smoke, Heat, and Carbon Monoxide Alarms, and Security Systems

Service-Entrance Equipment

Overcurrent Protectionfuses and Circuit Breakers

Service-Entrance Calculations

Swimming Pools, Spas, Hot Tubs, and Hydromassage Baths

Wiring for the Future: Home Automation Systems

Standby Power Systems

Residential Utility-Interactive Photovoltaic Systems

Filters

When terminating a receptacle, the white (grounded) conductor is always connected to the -colored terminal, and the phase (hot) conductor is always connected to the -colored terminal.