Question 1

When reassembling the 6R60 transmission, the intermediate support housing must be placed so the locating tabs are in the:

Accepted Answer

A)  "12:00" and "6:00" positions. 
B)  "3:00" and "9:00" positions. 
C)  "2:00" and "8:00" positions. 
D)  "10:00" and "5:00" positions. 
A)  "12:00" and "6:00" positions. 
B)  "3:00" and "9:00" positions. 
C)  "2:00" and "8:00" positions. 
D)  "10:00" and "5:00" positions.

Question 2

Technician A says that all pre-2011 transmissions will have a TCM mounted to the transmission valve body. Technician B says that all transmissions are controlled by the PCM, regardless of the year. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 3

When rebuilding the forward/overdrive clutch assembly, what should be the position of the new snap ring with respect to the position of the original snap ring opening?

Accepted Answer

A)  About 180 degrees away 
B)  Both should be the same 
C)  About 120 degrees away 
D)  About 90 degrees away 
A)  About 180 degrees away 
B)  Both should be the same 
C)  About 120 degrees away 
D)  About 90 degrees away

Question 4

Tech A states that the transmission fluid temperature is not related in any way to the transmission fluid level. Tech B states that if the fluid temperature is incorrect when the fluid level is checked, an incorrect reading may result. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 5

The 6R60 transmission range sensor has a duty cycle specification of 40.54-52.49 in the ________ position.

Accepted Answer

A)  reverse 
B)  park 
C)  neutral 
D)  drive 
A)  reverse 
B)  park 
C)  neutral 
D)  drive

Question 6

Tech A states that the 6R60 transmission does not contain any brake bands or dog clutches. Tech B states that the 6R60 transmission does not have a dog clutch, but uses brake bands. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 7

The 6R60 transmission range sensor has a duty cycle specification of 40.54-52.49 in the ________ position.

Accepted Answer

A)  reverse 
B)  park 
C)  neutral 
D)  drive 
A)  reverse 
B)  park 
C)  neutral 
D)  drive

Question 8

To obtain the six gear ratios, ________ multidisc clutches are used in the 6R60 transmission.

Accepted Answer

A)  two 
B)  four 
C)  six 
D)  five 
A)  two 
B)  four 
C)  six 
D)  five

Question 9

Tech A states that the 4th gear of a 6R60 transmission has a 1.14:1 ratio. Tech B states that the transmission does not have a true 1:1 ratio. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 10

Technician A says that some heavy-duty versions of the 6R60 transmission utilizes a one-way roller clutch to help with engine braking. Technician B says that the 6R80 is a heavy-duty versions of the 6R60 transmission. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 11

Identify the transmission fluid required by the Ford 6R60 transmission.

Accepted Answer

A)  ATF+4 
B)  ATF+1 
C)  MERCON LV 
D)  Type F ATF 
A)  ATF+4 
B)  ATF+1 
C)  MERCON LV 
D)  Type F ATF

Question 12

What is the duty cycle specification of a 6R60 transmission range sensor in the park position?

Accepted Answer

A)  18.1-25.8 
B)  30.50-39.31 
C)  70.55-85.61 
D)  54.35-68.15 
A)  18.1-25.8 
B)  30.50-39.31 
C)  70.55-85.61 
D)  54.35-68.15

Question 13

The sixth gear of a 6R60 transmission uses a gear ratio of ________

Accepted Answer

A)  2.84:1 
B)  1.9:1 
C)  0.69:1 
D)  1:1 
A)  2.84:1 
B)  1.9:1 
C)  0.69:1 
D)  1:1

Question 14

Identify the operating frequency of the transmission range sensor of a 6R60 transmission.

Accepted Answer

A)  200 to 250 Hz 
B)  100 to 150 Hz 
C)  250 to 300 Hz 
D)  50 to 100 Hz 
A)  200 to 250 Hz 
B)  100 to 150 Hz 
C)  250 to 300 Hz 
D)  50 to 100 Hz

Question 15

Identify the gear ratio of the fifth gear of a 6R60 transmission.

Accepted Answer

A)  1:1 
B)  0.87:1 
C)  4.7:1 
D)  2.84:1 
A)  1:1 
B)  0.87:1 
C)  4.7:1 
D)  2.84:1

Question 16

What does the transmission use to attain the six gear ratios?

Accepted Answer

A)  Dog clutches 
B)  One-way rollers 
C)  Multiple disc clutches 
D)  Brake bands 
A)  Dog clutches 
B)  One-way rollers 
C)  Multiple disc clutches 
D)  Brake bands

Question 17

A vehicle with a 6R60 transmission comes in to the shop with only 1st and 2nd gear. Tech A states the problem could be a bad low reverse clutch. Tech B states that the problem could be a bad range switch. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 18

Tech A states that the 6R60 transmission does not utilize a traditional dipstick. Tech B states that the transmission temperature must be around 180˚ F (82˚ C) in order to check the fluid. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 19

The Ford 6R60 transmission uses a single ________

Accepted Answer

A)  Lepelletier planetary gear 
B)  multidisc clutch 
C)  overdrive gear 
D)  shift solenoid 
A)  Lepelletier planetary gear 
B)  multidisc clutch 
C)  overdrive gear 
D)  shift solenoid

Question 20

When removing the snap ring during disassembly of the forward/overdrive clutch assembly, what precaution should be taken to prevent damage to the forward clutch housing?

Accepted Answer

A)  Pry only 180 degrees from the snap ring opening. 
B)  Remove the snap ring using a seal puller. 
C)  Pry only 90 degrees from the snap ring opening. 
D)  Remove the snap ring using a pick. 
A)  Pry only 180 degrees from the snap ring opening. 
B)  Remove the snap ring using a seal puller. 
C)  Pry only 90 degrees from the snap ring opening. 
D)  Remove the snap ring using a pick.

Exam 27: Ford 6r60 Zf6hp26

When reassembling the 6R60 transmission, the intermediate support housing must be placed so the locating tabs are in the:

Technician A says that all pre-2011 transmissions will have a TCM mounted to the transmission valve body. Technician B says that all transmissions are controlled by the PCM, regardless of the year. Who is correct?

When rebuilding the forward/overdrive clutch assembly, what should be the position of the new snap ring with respect to the position of the original snap ring opening?

Tech A states that the transmission fluid temperature is not related in any way to the transmission fluid level. Tech B states that if the fluid temperature is incorrect when the fluid level is checked, an incorrect reading may result. Who is correct?

The 6R60 transmission range sensor has a duty cycle specification of 40.54-52.49 in the ________ position.

Tech A states that the 6R60 transmission does not contain any brake bands or dog clutches. Tech B states that the 6R60 transmission does not have a dog clutch, but uses brake bands. Who is correct?

The 6R60 transmission range sensor has a duty cycle specification of 40.54-52.49 in the ________ position.

To obtain the six gear ratios, ________ multidisc clutches are used in the 6R60 transmission.

Tech A states that the 4th gear of a 6R60 transmission has a 1.14:1 ratio. Tech B states that the transmission does not have a true 1:1 ratio. Who is correct?

Technician A says that some heavy-duty versions of the 6R60 transmission utilizes a one-way roller clutch to help with engine braking. Technician B says that the 6R80 is a heavy-duty versions of the 6R60 transmission. Who is correct?

Identify the transmission fluid required by the Ford 6R60 transmission.

What is the duty cycle specification of a 6R60 transmission range sensor in the park position?

The sixth gear of a 6R60 transmission uses a gear ratio of ________

Identify the operating frequency of the transmission range sensor of a 6R60 transmission.

Identify the gear ratio of the fifth gear of a 6R60 transmission.

What does the transmission use to attain the six gear ratios?

A vehicle with a 6R60 transmission comes in to the shop with only 1st and 2nd gear. Tech A states the problem could be a bad low reverse clutch. Tech B states that the problem could be a bad range switch. Who is correct?

Tech A states that the 6R60 transmission does not utilize a traditional dipstick. Tech B states that the transmission temperature must be around 180˚ F (82˚ C) in order to check the fluid. Who is correct?

The Ford 6R60 transmission uses a single ________

When removing the snap ring during disassembly of the forward/overdrive clutch assembly, what precaution should be taken to prevent damage to the forward clutch housing?

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Allison 1000 and 2000 Series Transmissions

Filters