Question 1

Refer to the exhibit. If the network environment is operating normally, which type of device must be connected to interface FastEthernet 0/1?

Accepted Answer

A)  DHCP client 
B)  access point 
C)  router 
D)  PC 
A)  DHCP client 
B)  access point 
C)  router 
D)  PC

Question 2

How does CAPWAP communicate between an access point in local mode and a WLC?

Accepted Answer

A)  The access point must not be connected to the wired network, as it would create a loop 
B)  The access point must be connected to the same switch as the WLC 
C)  The access point must directly connect to the WLC using a copper cable 
D)  The access point has the ability to link to any switch in the network, assuming connectivity to the WLC 
A)  The access point must not be connected to the wired network, as it would create a loop 
B)  The access point must be connected to the same switch as the WLC 
C)  The access point must directly connect to the WLC using a copper cable 
D)  The access point has the ability to link to any switch in the network, assuming connectivity to the WLC

Question 3

Which command must be entered when a device is configured as an NTP server?

Accepted Answer

A)  ntp peer 
B)  ntp master 
C)  ntp authenticate 
D)  ntp server 
A)  ntp peer 
B)  ntp master 
C)  ntp authenticate 
D)  ntp server

Question 4

Which type of API allows SDN controllers to dynamically make changes to the network?

Accepted Answer

A)  northbound API 
B)  REST API 
C)  SOAP API 
D)  southbound API 
A)  northbound API 
B)  REST API 
C)  SOAP API 
D)  southbound API

Question 5

Which identity store option allows you to modify the directory services that run on TCP/IP?

Accepted Answer

A)  Lightweight Directory Access Protocol 
B)  RSA SecurID server 
C)  RADIUS 
D)  Active Directory 
A)  Lightweight Directory Access Protocol 
B)  RSA SecurID server 
C)  RADIUS 
D)  Active Directory

Question 6

When configuring a WLAN with WPA2 PSK in the Cisco Wireless LAN Controller GUI, which two formats are available to select? (Choose two.)

Accepted Answer

A)  decimal 
B)  ASCII 
C)  hexadecimal 
D)  binary 
E)  base64 
A)  decimal 
B)  ASCII 
C)  hexadecimal 
D)  binary 
E)  base64

Question 7

Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

Accepted Answer

A)  active 
B)  on 
C)  auto 
D)  desirable 
A)  active 
B)  on 
C)  auto 
D)  desirable

Question 8

Router A learns the same route from two different neighbors; one of the neighbor routers is an OSPF neighbor, and the other is an EIGRP neighbor. What is the administrative distance of the route that will be installed in the routing table?

Accepted Answer

A)  20 
B)  90 
C)  110 
D)  115 
A)  20 
B)  90 
C)  110 
D)  115

Question 9

When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?

Accepted Answer

A)  Passive 
B)  Desirable 
C)  On 
D)  Auto 
E)  Active 
A)  Passive 
B)  Desirable 
C)  On 
D)  Auto 
E)  Active

Question 10

Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)

Accepted Answer

A)  mismatched autonomous system numbers 
B)  an ACL blocking traffic from multicast address 224.0.0.10 
C)  mismatched process IDs 
D)  mismatched hello timers and dead timers 
E)  use of the same router ID on both devices 
A)  mismatched autonomous system numbers 
B)  an ACL blocking traffic from multicast address 224.0.0.10 
C)  mismatched process IDs 
D)  mismatched hello timers and dead timers 
E)  use of the same router ID on both devices

Question 11

Which two statements about eBGP neighbor relationships are true? (Choose two.)

Accepted Answer

A)  The two devices must reside in different autonomous systems 
B)  Neighbors must be specifically declared in the configuration of each device 
C)  They can be created dynamically after the network statement is configured 
D)  The two devices must reside in the same autonomous system 
E)  The two devices must have matching timer settings 
A)  The two devices must reside in different autonomous systems 
B)  Neighbors must be specifically declared in the configuration of each device 
C)  They can be created dynamically after the network statement is configured 
D)  The two devices must reside in the same autonomous system 
E)  The two devices must have matching timer settings

Question 12

While examining excessive traffic on the network, it is noted that all incoming packets on an interface appear to be allowed even though an IPv4 ACL is applied to the interface. Which two misconfigurations cause this behavior? (Choose two.)

Accepted Answer

A)  The ACL is empty 
B)  A matching permit statement is too broadly defined A matching permit statement is too broadly defined 
C)  The packets fail to match any permit statement The packets fail to match any statement 
D)  A matching deny statement is too high in the access list deny statement is too high in the access list 
E)  A matching permit statement is too high in the access list 
A)  The ACL is empty 
B)  A matching permit statement is too broadly defined A matching permit statement is too broadly defined 
C)  The packets fail to match any permit statement The packets fail to match any statement 
D)  A matching deny statement is too high in the access list deny statement is too high in the access list 
E)  A matching permit statement is too high in the access list

Question 13

Which command should you enter to verify the priority of a router in an HSRP group?

Accepted Answer

A)  show hsrp 
B)  show sessions 
C)  show interfaces 
D)  show standby 
A)  show hsrp 
B)  show sessions 
C)  show interfaces 
D)  show standby

Question 14

What is a network appliance that checks the state of a packet to determine whether the packet is legitimate?

Accepted Answer

A)  Layer 2 switch 
B)  LAN controller 
C)  load balancer 
D)  firewall 
A)  Layer 2 switch 
B)  LAN controller 
C)  load balancer 
D)  firewall

Question 15

Refer to the exhibit. Which two commands were used to create port channel 10? (Choose two.)

Accepted Answer

A)  int range g0/0-1 channel-group 10 mode active 
B)  channel-group 10 mode desirable 
C)  channel-group 10 mode passive 
D)  channel-group 10 mode auto 
E)  channel-group 10 mode on 
A)  int range g0/0-1 channel-group 10 mode active 
B)  channel-group 10 mode desirable 
C)  channel-group 10 mode passive 
D)  channel-group 10 mode auto 
E)  channel-group 10 mode on

Question 16

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

Accepted Answer

A)    
B)    
C)    
D)    
A)    
B)    
C)    
D)

Question 17

What protocol allows an engineer to back up 20 network router configurations globally while using the copy function?

Accepted Answer

A)  TCP 
B)  SMTP 
C)  FTP 
D)  SNMP 
A)  TCP 
B)  SMTP 
C)  FTP 
D)  SNMP

Question 18

An organization has decided to start using cloud-provided services. Which cloud service allows the organization to install its own operating system on a virtual machine?

Accepted Answer

A)  platform-as-a-service 
B)  network-as-a-service 
C)  software-as-a-service 
D)  infrastructure-as-a-service 
A)  platform-as-a-service 
B)  network-as-a-service 
C)  software-as-a-service 
D)  infrastructure-as-a-service

Question 19

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two.)

Accepted Answer

A)  Enable NTP authentication. 
B)  Verify the time zone. 
C)  Specify the IP address of the NTP server. 
D)  Set the NTP server private key. 
E)  Disable NTP broadcasts. 
A)  Enable NTP authentication. 
B)  Verify the time zone. 
C)  Specify the IP address of the NTP server. 
D)  Set the NTP server private key. 
E)  Disable NTP broadcasts.

Question 20

A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two.)

Accepted Answer

A)  input errors 
B)  frame 
C)  giants 
D)  CRC 
E)  runts 
A)  input errors 
B)  frame 
C)  giants 
D)  CRC 
E)  runts

Exam 4: Cisco Certified Network Associate (CCNA)

Refer to the exhibit. If the network environment is operating normally, which type of device must be connected to interface FastEthernet 0/1?

How does CAPWAP communicate between an access point in local mode and a WLC?

Which command must be entered when a device is configured as an NTP server?

Which type of API allows SDN controllers to dynamically make changes to the network?

Which identity store option allows you to modify the directory services that run on TCP/IP?

When configuring a WLAN with WPA2 PSK in the Cisco Wireless LAN Controller GUI, which two formats are available to select? (Choose two.)

Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

Router A learns the same route from two different neighbors; one of the neighbor routers is an OSPF neighbor, and the other is an EIGRP neighbor. What is the administrative distance of the route that will be installed in the routing table?

When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?

Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)

Which two statements about eBGP neighbor relationships are true? (Choose two.)

While examining excessive traffic on the network, it is noted that all incoming packets on an interface appear to be allowed even though an IPv4 ACL is applied to the interface. Which two misconfigurations cause this behavior? (Choose two.)

Which command should you enter to verify the priority of a router in an HSRP group?

What is a network appliance that checks the state of a packet to determine whether the packet is legitimate?

Refer to the exhibit. Which two commands were used to create port channel 10? (Choose two.)

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

What protocol allows an engineer to back up 20 network router configurations globally while using the copy function?

An organization has decided to start using cloud-provided services. Which cloud service allows the organization to install its own operating system on a virtual machine?

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two.)

A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two.)

Supporting Cisco Data Center System Devices (DCTECH)

Cisco Certified Technician Routing & Switching (RSTECH)

Understanding Cisco Cybersecurity Operations Fundamentals (CBROPS)

Managing Industrial Networks with Cisco Networking Technologies (IMINS)

DevNet Associate (DEVASC)

Conducting Forensic Analysis and Incident Response Using Cisco CyberOps Technologies (CBRFIR)

Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)

Implementing Cisco SD-WAN Solutions (ENSDWI)

Designing Cisco Enterprise Networks (ENSLD)

Designing Cisco Enterprise Wireless Networks (300-425 ENWLSD)

Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI)

Automating Cisco Enterprise Solutions (ENAUTO)

Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)

Implementing Cisco Service Provider VPN Services (SPVI)

Designing Cisco Data Center Infrastructure (DCID)

Troubleshooting Cisco Data Center Infrastructure (DCIT)

Implementing Cisco Application Centric Infrastructure (DCACI)

Configuring Cisco MDS 9000 Series Switches (DCSAN)

Implementing Cisco Application Centric Infrastructure - Advanced

Automating Cisco Data Center Solutions (DCAUTO)

Securing Networks with Cisco Firepower (300-710 SNCF)

Implementing and Configuring Cisco Identity Services Engine (300-715 SISE)

Securing Email with Cisco Email Security Appliance (300-720 SESA)

Securing the Web with Cisco Web Security Appliance (300-725 SWSA)

Implementing Secure Solutions with Virtual Private Networks (SVPN 300-730)

Automating Cisco Security Solutions (SAUTO)

Implementing Cisco Collaboration Applications (CLICA)

Implementing Cisco Advanced Call Control and Mobility Services (CLASSM)

Implementing Cisco Collaboration Cloud and Edge Solutions

Implementing Cisco Collaboration Conferencing

Automating Cisco Collaboration Solutions (CLAUTO)

Implementing DevOps Solutions and Practices using Cisco Platforms (DEVOPS)

Developing Solutions Using Cisco IoT and Edge Platforms (DEVIOT)

Developing Applications for Cisco Webex and Webex Devices (DEVWBX)

Performing CyberOps Using Core Security Technologies (CBRCOR)

Implementing Cisco Enterprise Network Core Technologies (ENCOR)

Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

Implementing and Operating Cisco Data Center Core Technologies (DCCOR)

Implementing and Operating Cisco Security Core Technologies

Implementing Cisco Collaboration Core Technologies (CLCOR)

Developing Applications using Cisco Core Platforms and APIs (DEVCOR)

CCDE Design Written

Deploying Cisco Unified Contact Center Express

Cisco Meraki Solutions Specialist

Securing Cisco Networks with Sourcefire FireAMP Endpoints

Designing Cisco Unified Contact Center Enterprise (UCCED)

Implementing and Supporting Cisco Unified Contact Center Enterprise (UCCEIS)

Cisco Collaboration SaaS Authorization Exam

Cisco Security Architecture for System Engineers

Adopting The Cisco Business Architecture Approach (DTBAA)

Cisco Customer Success Manager (CSM)

Mastering The Cisco Business Architecture Discipline (DTBAD)

Filters