Question 1

Identify the component shown in the graphic:

Accepted Answer

A) IDE connector 
B) Power supply connector 
C) SCSI connector 
D) SATA connector 
A) IDE connector 
B) Power supply connector 
C) SCSI connector 
D) SATA connector

Question 2

John wants to choose optimal hardware for his operating system. Which of the following can provide dependable information on compatibility between OS and hardware devices?

Accepted Answer

A) MCL 
B) HCL 
C) SCL 
D) RCL 
A) MCL 
B) HCL 
C) SCL 
D) RCL

Question 3

Which of the following ATA specifications is capable of data transfer rates of up to 33 MBps?

Accepted Answer

A) Ultra-ATA 
B) ATA 
C) ATA-2 
D) Fast ATA 
A) Ultra-ATA 
B) ATA 
C) ATA-2 
D) Fast ATA

Question 4

A new 6U server is being installed in an existing server rack. How much room in inches is required for this server?

Accepted Answer

A) 6 inches (10.2 cm) 
B) 10.5 inches (15.3 cm) 
C) 9 inches (17.9 cm) 
D) 12 inches (20.4 cm) 
A) 6 inches (10.2 cm) 
B) 10.5 inches (15.3 cm) 
C) 9 inches (17.9 cm) 
D) 12 inches (20.4 cm)

Question 5

John hears a whining noise when he starts his server. Which of the following could be the most likely issue?

Accepted Answer

A) Faulty processor 
B) Processor failure 
C) Faulty RAM 
D) Power supply failure 
A) Faulty processor 
B) Processor failure 
C) Faulty RAM 
D) Power supply failure

Question 6

Which of the following does an ESD wrist strap or mat contain that helps remove ESD charges safely?

Accepted Answer

A) Resistor 
B) Inductor 
C) Diode 
D) Capacitor 
A) Resistor 
B) Inductor 
C) Diode 
D) Capacitor

Question 7

John took a full tape backup of a server at 3:00 p.m. Sunday morning, and differential backup tapes were recorded every day at their specified p.m. time periods.. On Tuesday, at 11:00 a.m. the server crashed. How many tapes are required to restore the system?

Accepted Answer

A) 4 
B) 2 
C) 1 
D) 3 
A) 4 
B) 2 
C) 1 
D) 3

Question 8

Which of the following specifies the prime difference between UTP and STP networking cables?

Accepted Answer

A) STP has an additional layer of insulation surrounding the four-pair wire bundle. 
B) UTP has an additional layer of insulation surrounding the four-pair wire bundle. 
C) UTP ha an additional foil shield surrounding the four-pair wire bundle. 
D) STP has an additional foil shield surrounding the four-pair wire bundle. 
A) STP has an additional layer of insulation surrounding the four-pair wire bundle. 
B) UTP has an additional layer of insulation surrounding the four-pair wire bundle. 
C) UTP ha an additional foil shield surrounding the four-pair wire bundle. 
D) STP has an additional foil shield surrounding the four-pair wire bundle.

Question 9

You want to implement a Fiber Channel infrastructure between two branch offices that that are 4 km apart. Which of the following Fiber Channel cables should you use?

Accepted Answer

A) Multimode cable 
B) Duplex cable 
C) Simplex cable 
D) Single-mode cable 
A) Multimode cable 
B) Duplex cable 
C) Simplex cable 
D) Single-mode cable

Question 10

David's server is not able to detect a hot-plug NIC that is plugged in as a replacement. Which of the following specifies the first troubleshooting step to perform?

Accepted Answer

A) Check if the hot-plug PCI slot has been reactivated. 
B) Use the Windows configuration tools to define the NIC as a software. 
C) Replace the NIC. 
D) Configure the NIC to transmit both LAN and storage communications. 
A) Check if the hot-plug PCI slot has been reactivated. 
B) Use the Windows configuration tools to define the NIC as a software. 
C) Replace the NIC. 
D) Configure the NIC to transmit both LAN and storage communications.

Question 11

John wants to install a new application on all employee computers. The employees are concerned that the computer will slow down if the application is installed. What should John do?

Accepted Answer

A) Run an installation baseline on employee systems and test the performance. 
B) Should not install the new program, based on the concerns of the affected employees. 
C) Skip the baseline and install the new program. 
D) Run an installation baseline on the test system first and test the performance. 
A) Run an installation baseline on employee systems and test the performance. 
B) Should not install the new program, based on the concerns of the affected employees. 
C) Skip the baseline and install the new program. 
D) Run an installation baseline on the test system first and test the performance.

Question 12

Which of the following factors is the most important consideration while configuring a baseline?

Accepted Answer

A) Time taken to evaluate the baseline 
B) The baseline measurements that are documented 
C) The software used to record the baseline 
D) The role of the server 
A) Time taken to evaluate the baseline 
B) The baseline measurements that are documented 
C) The software used to record the baseline 
D) The role of the server

Question 13

You are trying to isolate a specific software problem. During which of the following operations, an error occurrence can be categorized as an operational error?

Accepted Answer

A) When the PC is booting 
B) When you are upgrading the operating system 
C) When you installing the operating system 
D) When the system is booted and you are on the OS 
A) When the PC is booting 
B) When you are upgrading the operating system 
C) When you installing the operating system 
D) When the system is booted and you are on the OS

Question 14

Which of the following tape formats maximizes the storage of a DAT drive?

Accepted Answer

A) Travan 
B) QIC 
C) DDS 
D) DSS 
A) Travan 
B) QIC 
C) DDS 
D) DSS

Question 15

David has installed multiple processors on his computer. However, the system recognizes only one processor. Which of the following could be the possible cause of this issue?

Accepted Answer

A) Processor speed mismatch 
B) Additional VRMs are not used 
C) Empty processor slots do not have terminator resistor packs. 
D) The OS is not configured to use multiple processors. 
A) Processor speed mismatch 
B) Additional VRMs are not used 
C) Empty processor slots do not have terminator resistor packs. 
D) The OS is not configured to use multiple processors.

Question 16

John is managing a server that has four internal hard drives. POST only indicates that two HDDs are installed. Which of the following could be the most likely cause of this issue?

Accepted Answer

A) Two of the four are SCSI hard drives. 
B) Disks are configured in two separate RAID arrays. 
C) Disks are configured in a RAID 1 mirrored array. 
D) Disks are configured in a RAID 0 striped array. 
A) Two of the four are SCSI hard drives. 
B) Disks are configured in two separate RAID arrays. 
C) Disks are configured in a RAID 1 mirrored array. 
D) Disks are configured in a RAID 0 striped array.

Question 17

Which of the following hard drive specifications supports data transfer rates of up to 150 MBps?

Accepted Answer

A) Ultra-ATA 
B) Serial ATA 
C) Fast SCSI 
D) ATA 
A) Ultra-ATA 
B) Serial ATA 
C) Fast SCSI 
D) ATA

Question 18

Which of the following is the IRQ that can be used by either COM 1 or COM 3?

Accepted Answer

A) 4 
B) 0 
C) 1 
D) 3 
A) 4 
B) 0 
C) 1 
D) 3

Exam 26: Server

Identify the component shown in the graphic:

John wants to choose optimal hardware for his operating system. Which of the following can provide dependable information on compatibility between OS and hardware devices?

Which of the following ATA specifications is capable of data transfer rates of up to 33 MBps?

A new 6U server is being installed in an existing server rack. How much room in inches is required for this server?

John hears a whining noise when he starts his server. Which of the following could be the most likely issue?

Which of the following does an ESD wrist strap or mat contain that helps remove ESD charges safely?

John took a full tape backup of a server at 3:00 p.m. Sunday morning, and differential backup tapes were recorded every day at their specified p.m. time periods.. On Tuesday, at 11:00 a.m. the server crashed. How many tapes are required to restore the system?

Which of the following specifies the prime difference between UTP and STP networking cables?

You want to implement a Fiber Channel infrastructure between two branch offices that that are 4 km apart. Which of the following Fiber Channel cables should you use?

David's server is not able to detect a hot-plug NIC that is plugged in as a replacement. Which of the following specifies the first troubleshooting step to perform?

John wants to install a new application on all employee computers. The employees are concerned that the computer will slow down if the application is installed. What should John do?

Which of the following factors is the most important consideration while configuring a baseline?

You are trying to isolate a specific software problem. During which of the following operations, an error occurrence can be categorized as an operational error?

Which of the following tape formats maximizes the storage of a DAT drive?

David has installed multiple processors on his computer. However, the system recognizes only one processor. Which of the following could be the possible cause of this issue?

John is managing a server that has four internal hard drives. POST only indicates that two HDDs are installed. Which of the following could be the most likely cause of this issue?

Which of the following hard drive specifications supports data transfer rates of up to 150 MBps?

Which of the following is the IRQ that can be used by either COM 1 or COM 3?

Hardware

Laptops

Networking

Printers

Procedures

Other Operating Systems and Technologies

Mobile-Devices

Operating-Systems

Security

Troubleshooting

Access-Identity

Apps - Data - Host

Compliance-Op

Comptia Asp

Concepts

Cryptography

Dhti

Enrolled-Agent

Essentials

Install Configure

Linux

Management

Media Topologies

Network

Other-Operating-Systems-And-Technologies

Software-Troubleshooting

Threats

Filters