Question 1

If there is no electric control of the Chrysler 62TE transmission, what gears will still function?

Accepted Answer

A)  Reverse, third 
B)  First, third 
C)  Second, third 
D)  Low, reverse 
A)  Reverse, third 
B)  First, third 
C)  Second, third 
D)  Low, reverse

Question 2

Solenoid testing of a Chrysler 62TE transmission are being discussed. Technician A says that each solenoid can be tested directly. Technician B says that if a solenoid is determined to be faulty, the entire solenoid assembly should be replaced. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both Technicians A and B 
D)  Neither Technician A nor B 
A)  Technician A 
B)  Technician B 
C)  Both Technicians A and B 
D)  Neither Technician A nor B

Question 3

When installing new sealing rings onto the low clutch housing, the entire housing must be replaced if the amount of clearance between the sealing ring and the groove is more than:

Accepted Answer

A)  0.1 inch (2.54 mm). 
B)  0.1 mm (0.004 in). 
C)  0.01 inch (0.25 mm). 
D)  0.01 mm (0.0004 in). 
A)  0.1 inch (2.54 mm). 
B)  0.1 mm (0.004 in). 
C)  0.01 inch (0.25 mm). 
D)  0.01 mm (0.0004 in).

Question 4

Technician A says that there are five pressure switches built into the solenoid body assembly that are monitored by the PCM to verify correct clutches are applied. Technician B says that the five pressure solenoids are supplied 12 volts and should have a resistance of 300 ohms with pressure applied to them. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 5

A vehicle comes into the shop with the transmission stuck in 1st gear. Tech A states this could be caused by a failed output shaft speed sensor. Tech B states this could be caused by a faulty underdrive clutch. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 6

A customer brings their vehicle into the shop complaining about poor performance. You test drive the vehicle and find that the transmission is only operating in 3rd gear. Tech A states that this could be cause by a bad 2/4 clutch. Tech B says this could be caused by the TCM not having power. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 7

Technician A says that the 62TE transmission uses a transmission range switch with four separate switches that identify the current gear selected by the driver. Technician B says that these switches will either be open or closed. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 8

The Chrysler 62TE transmission is being discussed. Technician A says that there are 11 solenoids that operate the transmission. Technician B says that these 11 solenoids control shutter valve operation. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both Technicians A and B 
D)  Neither Technicians A nor B 
A)  Technician A 
B)  Technician B 
C)  Both Technicians A and B 
D)  Neither Technicians A nor B

Question 9

Identify the transmission fluid level for a fluid temperature of 138 degree Fahrenheit.

Accepted Answer

A)  55-62 mm 
B)  15-25 mm 
C)  29-42 mm 
D)  46-54 mm 
A)  55-62 mm 
B)  15-25 mm 
C)  29-42 mm 
D)  46-54 mm

Question 10

When rebuilding the transmission case, the retaining bolts of the pinion gear cover should be torqued to:

Accepted Answer

A)  2 to 8 in-lb (0.23-0.90 N·m). 
B)  45 ft-lb (61.01 N·m). 
C)  200 ft-lb (271.16 N·m). 
D)  105 in-lb (11.86 N·m). 
A)  2 to 8 in-lb (0.23-0.90 N·m). 
B)  45 ft-lb (61.01 N·m). 
C)  200 ft-lb (271.16 N·m). 
D)  105 in-lb (11.86 N·m).

Question 11

Identify the component of 62TE transmission shown in the given figure

Accepted Answer

A)  Variable force solenoid 
B)  Transmission case 
C)  Hex-style plug 
D)  Transfer shaft 
A)  Variable force solenoid 
B)  Transmission case 
C)  Hex-style plug 
D)  Transfer shaft

Question 12

During reassembly of the 62TE transmission case, if the turning torque of the pinion gear is not between 2 and 8 inch pounds, what should be replaced?

Accepted Answer

A)  Pinion gear cover 
B)  Different pinion gear 
C)  The select thickness shims 
D)  Different pinion bearings 
A)  Pinion gear cover 
B)  Different pinion gear 
C)  The select thickness shims 
D)  Different pinion bearings

Question 13

What gear is the fail safe or limp-in gear for a 62TE transmission?

Accepted Answer

A)  First 
B)  Second 
C)  Third 
D)  Fourth 
A)  First 
B)  Second 
C)  Third 
D)  Fourth

Question 14

Which of the following solenoids have a resistance specification of 5 ohms in the 62TE transmission?

Accepted Answer

A)  Line pressure, converter clutch 
B)  Low, low reverse 
C)  Underdrive clutch, overdrive 
D)  2/4 clutch, direct 
A)  Line pressure, converter clutch 
B)  Low, low reverse 
C)  Underdrive clutch, overdrive 
D)  2/4 clutch, direct

Question 15

Tech A states that the entire speedometer cable needs to be inserted inside the transmission to check the fluid level. Tech B states that it is very easy to push the speedometer cable past the dipstick stop inside the transmission. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A and B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A and B

Question 16

Choose the correct statement with respect to disassembling the 62TE transmission.

Accepted Answer

A)  Use a gear puller to remove the transfer drive gear and selective shim. 
B)  The six accumulator pistons and springs are not interchangeable. 
C)  If the line pressure plug is a hex-style plug, it can be left in the case. 
D)  If the line pressure plug is an Allen-style, it will need to be removed. 
A)  Use a gear puller to remove the transfer drive gear and selective shim. 
B)  The six accumulator pistons and springs are not interchangeable. 
C)  If the line pressure plug is a hex-style plug, it can be left in the case. 
D)  If the line pressure plug is an Allen-style, it will need to be removed.

Question 17

Technician A says that the 62TE transmission utilizes a double swap shift. Technician B says that the sensors in the transmission are used to determine any gear ratio errors. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 18

A vehicle comes into the shop with soft shifts. You measure line pressure and find that the line pressure is low. You check the voltage coming out of the transmission pressure sensor and find that it is 5 volts. Tech A states that the vehicle has a problem with the line pressure sensor. Tech B states that the vehicle needs a new pump or line pressure solenoid. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 19

Identify the type of transmission fluid that is required by 62TE.

Accepted Answer

A)  ATF+4 
B)  ATF+3 
C)  ATF+2 
D)  ATF+1 
A)  ATF+4 
B)  ATF+3 
C)  ATF+2 
D)  ATF+1

Question 20

Choose the correct statement with respect to solenoids in the 62TE transmission.

Accepted Answer

A)  The clutch solenoids operate a shuttle valve. 
B)  In 3rd gear, the underdrive clutch solenoid and the 2-4 clutch solenoid will allow fluid flow to their respective clutches. 
C)  The solenoids can be tested directly. 
D)  The solenoids can be replaced individually. 
A)  The clutch solenoids operate a shuttle valve. 
B)  In 3rd gear, the underdrive clutch solenoid and the 2-4 clutch solenoid will allow fluid flow to their respective clutches. 
C)  The solenoids can be tested directly. 
D)  The solenoids can be replaced individually.

Exam 24: Chrysler 6 Speed 62te Transmission

If there is no electric control of the Chrysler 62TE transmission, what gears will still function?

Solenoid testing of a Chrysler 62TE transmission are being discussed. Technician A says that each solenoid can be tested directly. Technician B says that if a solenoid is determined to be faulty, the entire solenoid assembly should be replaced. Who is correct?

When installing new sealing rings onto the low clutch housing, the entire housing must be replaced if the amount of clearance between the sealing ring and the groove is more than:

A vehicle comes into the shop with the transmission stuck in 1st gear. Tech A states this could be caused by a failed output shaft speed sensor. Tech B states this could be caused by a faulty underdrive clutch. Who is correct?

Technician A says that the 62TE transmission uses a transmission range switch with four separate switches that identify the current gear selected by the driver. Technician B says that these switches will either be open or closed. Who is correct?

The Chrysler 62TE transmission is being discussed. Technician A says that there are 11 solenoids that operate the transmission. Technician B says that these 11 solenoids control shutter valve operation. Who is correct?

Identify the transmission fluid level for a fluid temperature of 138 degree Fahrenheit.

When rebuilding the transmission case, the retaining bolts of the pinion gear cover should be torqued to:

Identify the component of 62TE transmission shown in the given figure

During reassembly of the 62TE transmission case, if the turning torque of the pinion gear is not between 2 and 8 inch pounds, what should be replaced?

What gear is the fail safe or limp-in gear for a 62TE transmission?

Which of the following solenoids have a resistance specification of 5 ohms in the 62TE transmission?

Tech A states that the entire speedometer cable needs to be inserted inside the transmission to check the fluid level. Tech B states that it is very easy to push the speedometer cable past the dipstick stop inside the transmission. Who is correct?

Choose the correct statement with respect to disassembling the 62TE transmission.

Technician A says that the 62TE transmission utilizes a double swap shift. Technician B says that the sensors in the transmission are used to determine any gear ratio errors. Who is correct?

Identify the type of transmission fluid that is required by 62TE.

Choose the correct statement with respect to solenoids in the 62TE transmission.

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters