Question 1

Which of the following methods are supported by VRP platform to configure the router? (Choose three)

Accepted Answer

A)  Through the Console port 
B)  Through Telnet 
C)  Through the AUX port 
D)  Through FTP 
A)  Through the Console port 
B)  Through Telnet 
C)  Through the AUX port 
D)  Through FTP

Question 2

In the VRP system, what are the functions of Ctrl+Z?

Accepted Answer

A)  Return from the system view to the user view 
B)  Exit from the current view 
C)  Exit from the interface view 
D)  Exit from the console interface view 
E)  Return to the user view 
A)  Return from the system view to the user view 
B)  Exit from the current view 
C)  Exit from the interface view 
D)  Exit from the console interface view 
E)  Return to the user view

Question 3

In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following? (Choose all that apply.)

Accepted Answer

A)  Maximum number of Up member links 
B)  Minimum number of Up member links 
C)  Number of Up member interfaces 
D)  Number of interfaces. 
A)  Maximum number of Up member links 
B)  Minimum number of Up member links 
C)  Number of Up member interfaces 
D)  Number of interfaces.

Question 4

If an Ethernet data frame carries Length/Type = 0x8100, which of the following cannot be the payload of the data frame?

Accepted Answer

A)  RSTP data frame 
B)  OSPF packet 
C)  ARP response packet 
D)  STP data frame 
A)  RSTP data frame 
B)  OSPF packet 
C)  ARP response packet 
D)  STP data frame

Question 5

Refer to the display output. Which statement is false?

Accepted Answer

A) The current configuration file has not been saved. B) The current startup system software is ar2220-v200r003c00spc200.cc C) The next startup system software cannot be changed. D) The next startup system software can be changed by using the "startup system software .cc" command. A) The current configuration file has not been saved. B) The current startup system software is ar2220-v200r003c00spc200.cc C) The next startup system software cannot be changed. D) The next startup system software can be changed by using the "startup system software .cc" command.

Question 6

MCU8660 size is ( ) U, wherein the system Single-Board representing the height ( ) U.

Accepted Answer

A)  20, 9 
B)  21, 9 
C)  21, 10 
D)  20, 10 
A)  20, 9 
B)  21, 9 
C)  21, 10 
D)  20, 10

Question 7

Host A has been connected to switch A and configured with an IP address. When Host A initially forwards a frame, what action will be taken by Switch A?

Accepted Answer

A)  Switch A will drop this frame. 
B)  Switch A will attempt to flood the frame to all ports except for the G0/0/1 interface. 
C)  Switch A will forward the frame via ports G0/0/1, G0/0/2 and G0/0/3. 
D)  Switch will receive this frame before returning the frame to G0/0/1. 
A)  Switch A will drop this frame. 
B)  Switch A will attempt to flood the frame to all ports except for the G0/0/1 interface. 
C)  Switch A will forward the frame via ports G0/0/1, G0/0/2 and G0/0/3. 
D)  Switch will receive this frame before returning the frame to G0/0/1.

Question 8

In TP3106, what does 3 represent?

Accepted Answer

A)  Number of screens 
B)  algebra 
C)  Number of seats 
D)  Model 
A)  Number of screens 
B)  algebra 
C)  Number of seats 
D)  Model

Question 9

Refer to the configuration output. Which of the following statements are correct regarding the configuration of the ACL on RTA? (Choose two).

Accepted Answer

A)  Packets from network 172.16.1.1/32 will be denied. 
B)  Packets from network 172.16.1.0/24 will be denied. 
C)  Packets from network 172.17.1.0/24 will be denied. 
D)  Packets from network 172.18.0.0/16 will be denied. 
A)  Packets from network 172.16.1.1/32 will be denied. 
B)  Packets from network 172.16.1.0/24 will be denied. 
C)  Packets from network 172.17.1.0/24 will be denied. 
D)  Packets from network 172.18.0.0/16 will be denied.

Question 10

Which of the following encapsulation modes is/are supported by IPsec VPN?

Accepted Answer

A)  Routing mode 
B)  Tunnel mode 
C)  Transport mode 
D)  Switching mode. 
A)  Routing mode 
B)  Tunnel mode 
C)  Transport mode 
D)  Switching mode.

Question 11

An administrator wishes to manage the router in the remote branch office, which method can be used?

Accepted Answer

A)  Telnet 
B)  FTP 
C)  Console Connection 
D)  DHCP 
A)  Telnet 
B)  FTP 
C)  Console Connection 
D)  DHCP

Question 12

In standard STP mode, which of the following ports on non-root switches forward the BPDUs with TC bits set generated by the root switch?

Accepted Answer

A)  Root port 
B)  Backup port 
C)  Designated port 
D)  Alternate port 
A)  Root port 
B)  Backup port 
C)  Designated port 
D)  Alternate port

Question 13

A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been configured using the command "authorization-mode hwtacacs if-authenticated". Which of the following statements regarding this command are true? (Choose three).

Accepted Answer

A)  If the hwtacacs server fails to respond, the user will be authenticated using local authentication. 
B)  If the hwtacacs server fails to respond, the user will be authenticated using remote authentication. 
C)  If the hwtacacs server fails to respond, the user will bypass authentication. 
D)  The hwtacacs server will authorize the user. 
A)  If the hwtacacs server fails to respond, the user will be authenticated using local authentication. 
B)  If the hwtacacs server fails to respond, the user will be authenticated using remote authentication. 
C)  If the hwtacacs server fails to respond, the user will bypass authentication. 
D)  The hwtacacs server will authorize the user.

Question 14

The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which message will the host first send to the DHCP server?

Accepted Answer

A)  DHCP DISCOVER 
B)  DHCP REQUEST 
C)  DHCP OFFER 
D)  DHCP ACK 
A)  DHCP DISCOVER 
B)  DHCP REQUEST 
C)  DHCP OFFER 
D)  DHCP ACK

Question 15

On the network shown in the figure, after the OSPF protocol state is stable, what is the neighbor status between Router A and Router B?

Accepted Answer

A)  Attempt 
B)  Full 
C)  2-way 
D)  Down 
A)  Attempt 
B)  Full 
C)  2-way 
D)  Down

Question 16

The PPPoE session establishment process can be divided into which stages? (Choose all that apply.)

Accepted Answer

A)  Discovery stage 
B)  DHCP stage 
C)  PPPoE Session stage 
D)  PPP connecting stage. 
A)  Discovery stage 
B)  DHCP stage 
C)  PPPoE Session stage 
D)  PPP connecting stage.

Question 17

On the network shown in the figure, all routers run OSPF and the cost value is above the link. Which of the following is the path for Router A to send packets to 10.0.0.0/8?

Accepted Answer

A)  A-B-D 
B)  A-C-D 
C)  RA fails to reach 10.0.0.0/8. 
D)  A-D 
A)  A-B-D 
B)  A-C-D 
C)  RA fails to reach 10.0.0.0/8. 
D)  A-D

Question 18

Which of the following statements regarding layer-2 switch is incorrect?

Accepted Answer

A)  The switch learns MAC addresses automatically. 
B)  The layer-3 header is modified before the received packet is transmitted. 
C)  The layer-2 header is modified before the received packet is transmitted. 
D)  The layer-2 LAN switch operates at data link layer. 
A)  The switch learns MAC addresses automatically. 
B)  The layer-3 header is modified before the received packet is transmitted. 
C)  The layer-2 header is modified before the received packet is transmitted. 
D)  The layer-2 LAN switch operates at data link layer.

Question 19

PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)

Accepted Answer

A)  PAP 
B)  MD5 
C)  CHAP 
D)  SSH 
A)  PAP 
B)  MD5 
C)  CHAP 
D)  SSH

Question 20

Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as expected and performs debugging. Based on the output from the debug, what is the source of the problem?

Accepted Answer

A)  R2 has configured an ACL to block the route to network 1.0.0.0 
B)  R2 has enabled split horizon. 
C)  R1 is using authentication, however R2 is not. 
D)  R2 is operating using RIPv2, while R1 is using RIPv1. 
A)  R2 has configured an ACL to block the route to network 1.0.0.0 
B)  R2 has enabled split horizon. 
C)  R1 is using authentication, however R2 is not. 
D)  R2 is operating using RIPv2, while R1 is using RIPv1.

Which of the following methods are supported by VRP platform to configure the router? (Choose three)

In the VRP system, what are the functions of Ctrl+Z?

In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following? (Choose all that apply.)

If an Ethernet data frame carries Length/Type = 0x8100, which of the following cannot be the payload of the data frame?

Refer to the display output. Which statement is false?

MCU8660 size is ( ) U, wherein the system Single-Board representing the height ( ) U.

Host A has been connected to switch A and configured with an IP address. When Host A initially forwards a frame, what action will be taken by Switch A?

In TP3106, what does 3 represent?

Refer to the configuration output. Which of the following statements are correct regarding the configuration of the ACL on RTA? (Choose two).

Which of the following encapsulation modes is/are supported by IPsec VPN?

An administrator wishes to manage the router in the remote branch office, which method can be used?

In standard STP mode, which of the following ports on non-root switches forward the BPDUs with TC bits set generated by the root switch?

A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been configured using the command "authorization-mode hwtacacs if-authenticated". Which of the following statements regarding this command are true? (Choose three).

The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which message will the host first send to the DHCP server?

On the network shown in the figure, after the OSPF protocol state is stable, what is the neighbor status between Router A and Router B?

The PPPoE session establishment process can be divided into which stages? (Choose all that apply.)

On the network shown in the figure, all routers run OSPF and the cost value is above the link. Which of the following is the path for Router A to send packets to 10.0.0.0/8?

Which of the following statements regarding layer-2 switch is incorrect?

PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)

Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as expected and performs debugging. Based on the output from the debug, what is the source of the problem?

HCNA-VC (Huawei Certified Network Associate - Video Conference)

HCNP-R&S-IERN (Huawei Certified Network Professional-Implementing Enterprise Routing Network)

HCNP-R&S-IENPÂ (Huawei Certified Network Professional-Improving Enterprise Network Performance)

HCNP-R&S Fast Track (Huawei Certified Network Professional - Routing & Switching Fast Track)

HCIE-R&S (Written) (Huawei Certified Internetwork Expert-Routing & Switching)

HCNA-Security-CBSN (Huawei Certified Network Associate - Constructing Basic Security Network)

HCNA-Storage-BSSN (Huawei Certified Network Associate - Building the Structure of Storage Network)

HCNA-Storage-BSSN

Huawei Certified Network Professional- Constructing Big Data Solution

HCIE-Storage

HCIA-Cloud Service V2.2

Huawei Certified Pre-sales Associate-IP Network(Datacom)-ENU

Huawei Certified Pre-sales Associate - ECC (HCPA-ECC)

HCNA - Carrier IP

HCIP-Cloud Computing-CDSM

HCIA-SDN

Filters

Exam 2: HHCIA Routing&Switching

Which of the following methods are supported by VRP platform to configure the router? (Choose three)

In the VRP system, what are the functions of Ctrl+Z?

In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following? (Choose all that apply.)

If an Ethernet data frame carries Length/Type = 0x8100, which of the following cannot be the payload of the data frame?

Refer to the display output. Which statement is false?

MCU8660 size is ( ) U, wherein the system Single-Board representing the height ( ) U.

Host A has been connected to switch A and configured with an IP address. When Host A initially forwards a frame, what action will be taken by Switch A?

In TP3106, what does 3 represent?

Refer to the configuration output. Which of the following statements are correct regarding the configuration of the ACL on RTA? (Choose two).

Which of the following encapsulation modes is/are supported by IPsec VPN?

An administrator wishes to manage the router in the remote branch office, which method can be used?

In standard STP mode, which of the following ports on non-root switches forward the BPDUs with TC bits set generated by the root switch?

A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been configured using the command "authorization-mode hwtacacs if-authenticated". Which of the following statements regarding this command are true? (Choose three).

The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which message will the host first send to the DHCP server?

On the network shown in the figure, after the OSPF protocol state is stable, what is the neighbor status between Router A and Router B?

The PPPoE session establishment process can be divided into which stages? (Choose all that apply.)

On the network shown in the figure, all routers run OSPF and the cost value is above the link. Which of the following is the path for Router A to send packets to 10.0.0.0/8?

Which of the following statements regarding layer-2 switch is incorrect?

PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)

Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as expected and performs debugging. Based on the output from the debug, what is the source of the problem?

HCNA-VC (Huawei Certified Network Associate - Video Conference)

HCNP-R&S-IERN (Huawei Certified Network Professional-Implementing Enterprise Routing Network)

HCNP-R&S-IENPÂ (Huawei Certified Network Professional-Improving Enterprise Network Performance)

HCNP-R&S Fast Track (Huawei Certified Network Professional - Routing & Switching Fast Track)

HCIE-R&S (Written) (Huawei Certified Internetwork Expert-Routing & Switching)

HCNA-Security-CBSN (Huawei Certified Network Associate - Constructing Basic Security Network)

HCNA-Storage-BSSN (Huawei Certified Network Associate - Building the Structure of Storage Network)

HCNA-Storage-BSSN

Huawei Certified Network Professional- Constructing Big Data Solution

HCIE-Storage

HCIA-Cloud Service V2.2

Huawei Certified Pre-sales Associate-IP Network(Datacom)-ENU

Huawei Certified Pre-sales Associate - ECC (HCPA-ECC)

HCNA - Carrier IP

HCIP-Cloud Computing-CDSM

HCIA-SDN

Filters