Question 1

Which of the following VRP commands can be used to enter area 0 view? (Choose two)

Accepted Answer

A)  [Huawei]ospf area 0 
B)  [Huawei-ospf-1]area 0 
C)  [Huawei-ospf-1]area 0.0.0.0 
D)  [Huawei-ospf-1]area 0 enable 
A)  [Huawei]ospf area 0 
B)  [Huawei-ospf-1]area 0 
C)  [Huawei-ospf-1]area 0.0.0.0 
D)  [Huawei-ospf-1]area 0 enable

Question 2

Which of the following values of the Length/Type field in an Ethernet data frame indicates the PPPoE discovery stage?

Accepted Answer

A)  0×8863 
B)  0×8864 
C)  0×0806 
D)  0×0800 
A)  0×8863 
B)  0×8864 
C)  0×0806 
D)  0×0800

Question 3

Which of the following statements explains the behavior of the ICMP redirect function? (Choose two)

Accepted Answer

A)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on the same segment as the next hop, an ICMP redirect message will be sent by the router to the source. 
B)  When a router receives data on an interface, and the router's IP address matches the destination IP of the data, an ICMP redirect message will be sent by the router to the source. 
C)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on the same segment as the next hop, an ICMP Redirect message will be sent by the source to the router. 
D)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on a different segment from the next hop, an ICMP redirect message will be sent by the router to the source 
A)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on the same segment as the next hop, an ICMP redirect message will be sent by the router to the source. 
B)  When a router receives data on an interface, and the router's IP address matches the destination IP of the data, an ICMP redirect message will be sent by the router to the source. 
C)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on the same segment as the next hop, an ICMP Redirect message will be sent by the source to the router. 
D)  When a router receives data on the interface via which the same data needs to be forwarded, and the source is on a different segment from the next hop, an ICMP redirect message will be sent by the router to the source

Question 4

According to the following topology and configuration, R1 and R2 are connected through low-speed serial cables and PPP is used to encapsulate data link layer packets. When the Holdtime values of R1 and R2 are different, PPP negotiation and communication fail.

Accepted Answer

A) True 
 B)False

Question 5

Which of the following OSPF packets can be used to confirm the received Link State Update (LSU) packets?

Accepted Answer

A)  LSR 
B)  LSA 
C)  LSU 
D)  LSACK 
A)  LSR 
B)  LSA 
C)  LSU 
D)  LSACK

Question 6

Assuming all STP enabled switches have the same bridge priority. The MAC address of switch A is 00-e0-fc-00-00-40, the MAC address of switch B is 00-e0-fc-00-00-10, the MAC address of switch C is 00-e0-fc-00-00-20, and the MAC address of switch D is 00-e0-fc-00-00-80. Which switch will be elected as the root switch?

Accepted Answer

A)  Switch A 
B)  Switch B 
C)  Switch C 
D)  Switch D 
A)  Switch A 
B)  Switch B 
C)  Switch C 
D)  Switch D

Question 7

A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The client assumed that the problem was with the port configuration. The blocking of which ports would likely cause this problem? (Choose two)

Accepted Answer

A)  21 
B)  80 
C)  20 
D)  50649 
A)  21 
B)  80 
C)  20 
D)  50649

Question 8

How many equipment does TP3106 contain? (Select two answers)

Accepted Answer

A)  AMX central control 
B)  Intelligence Host 
C)  Video Matrix 
D)  Relay 
A)  AMX central control 
B)  Intelligence Host 
C)  Video Matrix 
D)  Relay

Question 9

What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?

Accepted Answer

A)  remote logical channel ID 
B)  local DLCI 
C)  remote interface ID 
D)  remote node ID 
A)  remote logical channel ID 
B)  local DLCI 
C)  remote interface ID 
D)  remote node ID

Question 10

Which of the following statements about gratuitous ARP packets are true? (Choose two)

Accepted Answer

A)  A system can determine whether conflicting IP addresses are used by sending a gratuitous ARP packet 
B)  A gratuitous ARP packet uses the same format as an ARP request packet. 
C)  A gratuitous ARP packet can help to update an IP address. 
D)  A gratuitous ARP packet uses the same format as an ARP reply packet. 
A)  A system can determine whether conflicting IP addresses are used by sending a gratuitous ARP packet 
B)  A gratuitous ARP packet uses the same format as an ARP request packet. 
C)  A gratuitous ARP packet can help to update an IP address. 
D)  A gratuitous ARP packet uses the same format as an ARP reply packet.

Question 11

Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)

Accepted Answer

A)  The router IDs of OSPF routers in the same area must be the same, but can be different in different areas. 
B)  The router ID must be the IP address of an OSPF router interface. 
C)  The router ID must be configured manually. 
D)  A router running OSPF must have a router ID for it to operate properly. 
A)  The router IDs of OSPF routers in the same area must be the same, but can be different in different areas. 
B)  The router ID must be the IP address of an OSPF router interface. 
C)  The router ID must be configured manually. 
D)  A router running OSPF must have a router ID for it to operate properly.

Question 12

When configuring the PPP authentication method as PAP, which of the following operations are necessary? (Choose three)

Accepted Answer

A)  Add the user name and password of the authenticated party to the local user list. 
B)  Configure the encapsulation type of the interface connected to the peer as PPP. 
C)  Configure PPP authentication method as CHAP. 
D)  On the authenticated party end, configure the user name and password that are sent to authenticator. 
A)  Add the user name and password of the authenticated party to the local user list. 
B)  Configure the encapsulation type of the interface connected to the peer as PPP. 
C)  Configure PPP authentication method as CHAP. 
D)  On the authenticated party end, configure the user name and password that are sent to authenticator.

Question 13

Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after configuring the following commands: (Choose all that apply)

Accepted Answer

A)  RTA will have the route learned from the RTB 
B)  RTB will have the route learned from the RTA 
C)  RTA will have no neighbor relationship with RTB 
D)  RTB will have no neighbor relationship with RTA 
A)  RTA will have the route learned from the RTB 
B)  RTB will have the route learned from the RTA 
C)  RTA will have no neighbor relationship with RTB 
D)  RTB will have no neighbor relationship with RTA

Question 14

Which of the following statements regarding link-state database and routing-table of a "single" OSPF area are correct? (Choose two)

Accepted Answer

A)  The link-state databases that all routers build are identical. 
B)  The link-state databases that all routers build are different. 
C)  The routing-tables that all routers calculate are different. 
D)  The routing-tables that all routers calculate are identical. 
A)  The link-state databases that all routers build are identical. 
B)  The link-state databases that all routers build are different. 
C)  The routing-tables that all routers calculate are different. 
D)  The routing-tables that all routers calculate are identical.

Question 15

What is the value of the Type field in RSTP configuration BPDUs?

Accepted Answer

A)  0×00 
B)  0×01 
C)  0×02 
D)  0×03 
A)  0×00 
B)  0×01 
C)  0×02 
D)  0×03

Question 16

What is the total length of the port ID in STP?

Accepted Answer

A)  4 bits 
B)  8 bits 
C)  2 bits 
D)  16 bits 
A)  4 bits 
B)  8 bits 
C)  2 bits 
D)  16 bits

Question 17

If a route destined for the same network has multiple next hops, what is the route?

Accepted Answer

A)  Sub-optimal route 
B)  Multi-path route 
C)  Default route 
D)  Equal-cost route 
A)  Sub-optimal route 
B)  Multi-path route 
C)  Default route 
D)  Equal-cost route

Question 18

Which of the following IPv6 addresses is a multicast address?

Accepted Answer

A)  FF02::2E0:FCFF:FEEF:FEC 
B)  2000::2E0:FCFF:FEEF:FEC 
C)  FE80::2E0:FCFF:FEEF:FEC 
D)  FC00::2E0:FCFF:FEEF:FEC 
A)  FF02::2E0:FCFF:FEEF:FEC 
B)  2000::2E0:FCFF:FEEF:FEC 
C)  FE80::2E0:FCFF:FEEF:FEC 
D)  FC00::2E0:FCFF:FEEF:FEC

Question 19

Which of the following OSPF versions is specific to IPv6?

Accepted Answer

A)  OSPFv1 
B)  OSPFv2 
C)  OSPFv3 
D)  OSPFv4 
A)  OSPFv1 
B)  OSPFv2 
C)  OSPFv3 
D)  OSPFv4

Question 20

Which of the following statements are correct? (Choose two)

Accepted Answer

A)  A single collision domain exists between RTA and SWC. 
B)  A single broadcast domain exists between SWA and SWB. 
C)  A single collision domain exists between SWA and SWC. 
D)  A single broadcast domain exists between SWA and SWC. 
A)  A single collision domain exists between RTA and SWC. 
B)  A single broadcast domain exists between SWA and SWB. 
C)  A single collision domain exists between SWA and SWC. 
D)  A single broadcast domain exists between SWA and SWC.

Which of the following VRP commands can be used to enter area 0 view? (Choose two)

Which of the following values of the Length/Type field in an Ethernet data frame indicates the PPPoE discovery stage?

Which of the following statements explains the behavior of the ICMP redirect function? (Choose two)

According to the following topology and configuration, R1 and R2 are connected through low-speed serial cables and PPP is used to encapsulate data link layer packets. When the Holdtime values of R1 and R2 are different, PPP negotiation and communication fail.

Which of the following OSPF packets can be used to confirm the received Link State Update (LSU) packets?

A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The client assumed that the problem was with the port configuration. The blocking of which ports would likely cause this problem? (Choose two)

How many equipment does TP3106 contain? (Select two answers)

What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?

Which of the following statements about gratuitous ARP packets are true? (Choose two)

Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)

When configuring the PPP authentication method as PAP, which of the following operations are necessary? (Choose three)

Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after configuring the following commands: (Choose all that apply)

Which of the following statements regarding link-state database and routing-table of a "single" OSPF area are correct? (Choose two)

What is the value of the Type field in RSTP configuration BPDUs?

What is the total length of the port ID in STP?

If a route destined for the same network has multiple next hops, what is the route?

Which of the following IPv6 addresses is a multicast address?

Which of the following OSPF versions is specific to IPv6?

Which of the following statements are correct? (Choose two)

HCNA-VC (Huawei Certified Network Associate - Video Conference)

HCNP-R&S-IERN (Huawei Certified Network Professional-Implementing Enterprise Routing Network)

HCNP-R&S-IENPÂ (Huawei Certified Network Professional-Improving Enterprise Network Performance)

HCNP-R&S Fast Track (Huawei Certified Network Professional - Routing & Switching Fast Track)

HCIE-R&S (Written) (Huawei Certified Internetwork Expert-Routing & Switching)

HCNA-Security-CBSN (Huawei Certified Network Associate - Constructing Basic Security Network)

HCNA-Storage-BSSN (Huawei Certified Network Associate - Building the Structure of Storage Network)

HCNA-Storage-BSSN

Huawei Certified Network Professional- Constructing Big Data Solution

HCIE-Storage

HCIA-Cloud Service V2.2

Huawei Certified Pre-sales Associate-IP Network(Datacom)-ENU

Huawei Certified Pre-sales Associate - ECC (HCPA-ECC)

HCNA - Carrier IP

HCIP-Cloud Computing-CDSM

HCIA-SDN

Filters

Exam 2: HHCIA Routing&Switching

Which of the following VRP commands can be used to enter area 0 view? (Choose two)

Which of the following values of the Length/Type field in an Ethernet data frame indicates the PPPoE discovery stage?

Which of the following statements explains the behavior of the ICMP redirect function? (Choose two)

According to the following topology and configuration, R1 and R2 are connected through low-speed serial cables and PPP is used to encapsulate data link layer packets. When the Holdtime values of R1 and R2 are different, PPP negotiation and communication fail.

Which of the following OSPF packets can be used to confirm the received Link State Update (LSU) packets?

A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The client assumed that the problem was with the port configuration. The blocking of which ports would likely cause this problem? (Choose two)

How many equipment does TP3106 contain? (Select two answers)

What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?

Which of the following statements about gratuitous ARP packets are true? (Choose two)

Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)

When configuring the PPP authentication method as PAP, which of the following operations are necessary? (Choose three)

Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after configuring the following commands: (Choose all that apply)

Which of the following statements regarding link-state database and routing-table of a "single" OSPF area are correct? (Choose two)

What is the value of the Type field in RSTP configuration BPDUs?

What is the total length of the port ID in STP?

If a route destined for the same network has multiple next hops, what is the route?

Which of the following IPv6 addresses is a multicast address?

Which of the following OSPF versions is specific to IPv6?

Which of the following statements are correct? (Choose two)

HCNA-VC (Huawei Certified Network Associate - Video Conference)

HCNP-R&S-IERN (Huawei Certified Network Professional-Implementing Enterprise Routing Network)

HCNP-R&S-IENPÂ (Huawei Certified Network Professional-Improving Enterprise Network Performance)

HCNP-R&S Fast Track (Huawei Certified Network Professional - Routing & Switching Fast Track)

HCIE-R&S (Written) (Huawei Certified Internetwork Expert-Routing & Switching)

HCNA-Security-CBSN (Huawei Certified Network Associate - Constructing Basic Security Network)

HCNA-Storage-BSSN (Huawei Certified Network Associate - Building the Structure of Storage Network)

HCNA-Storage-BSSN

Huawei Certified Network Professional- Constructing Big Data Solution

HCIE-Storage

HCIA-Cloud Service V2.2

Huawei Certified Pre-sales Associate-IP Network(Datacom)-ENU

Huawei Certified Pre-sales Associate - ECC (HCPA-ECC)

HCNA - Carrier IP

HCIP-Cloud Computing-CDSM

HCIA-SDN

Filters