Exam 1: BICSI Registered Communications Distribution Designer - RCDD

What type of fiber optic cable is manufactured to protect individual glass strands and is primarily designed for use inside buildings?

(Multiple Choice)

4.9/5

(72)

Question 261

Cementitious materials are ________ based materials.

(Multiple Choice)

4.8/5

(68)

Question 262

You are designing multi band UHF police radio and VHF fire radio systems for a municipal office. Because of the closeness of the transmit and receive frequencies, you must ensure there is adequate filtering and gain control of the systems. Which device will best meet the ability to separate and control the transmit and receive signals?

(Multiple Choice)

4.9/5

(95)

Question 263

When selecting poles for aerial telecommunications facilities, which of the following is the class number for the strongest rated pole?

(Multiple Choice)

4.9/5

(87)

Question 264

When designing a fiber backbone using cable with an armored sheath, a major consideration that you must address is:

(Multiple Choice)

4.7/5

(72)

Question 265

An installation crew is pulling an optical fiber cable into a riser. The cable has an outside diameter of 25 mm (1 in). As the cable is being pulled off the reel and through a pulley into the riser, you must verify that the minimum bend radius for the cable being pulled is observed. The pulley must be sized at a MINIMUM of:

(Multiple Choice)

4.9/5

(77)

Question 266

One advantage of using preconnectorized jumpers and cables is:

(Multiple Choice)

4.9/5

(84)

Question 267

Select the appropriate task to complete the section 2.2 of the work breakdown structure below: 2. Technician 2.1 Install rack 2.2 _________ 2.3 Place fiber 2.4 Terminate fiber 2.5 Test fiber

(Multiple Choice)

4.7/5

(77)

Question 268

Which of the following covers lightning protection systems and defines as exposed anything above ground and outside the zone of protection?

(Multiple Choice)

4.8/5

(82)

Question 269

A ________ eliminates the need to remove or install materials.

(Multiple Choice)

4.8/5

(82)

Question 270

Exhibit: If a work breakdown structure (WBS) shows the tasks below, what is C, the successor task? A) Install OSP pathways B) Install fiber C) ________.

(Multiple Choice)

4.8/5

(74)

Question 271

What is the appropriate impedance of coaxial cable for use with broadband distribution?

(Multiple Choice)

5.0/5

(82)

Question 272

Color codes for cross-connections fields have been used for many years. Which color is used to identify campus backbone?

(Multiple Choice)

4.9/5

(68)

Question 273

What is the MAXIMUM horizontal cable length permitted for centralized optical fiber cabling from the MDA within a data center?

(Multiple Choice)

5.0/5

(75)

Question 274

You are placing PTP fiber between two locations 55 km (34 miles) apart. You are told that DWDM equipment will be installed within the next 5 years. Which of the following optical fiber types should you use?

(Multiple Choice)

4.8/5

(79)

Question 275

Which of the following is NOT a primary type of DAS antenna?

(Multiple Choice)

4.8/5

(61)

Question 276

Within a data center, if you have dual path connectivity between the primary entrance room and secondary entrance room, in addition to dual connectivity between these two rooms and the main distribution and secondary distribution areas, what tier level would this infrastructure design represent?

(Multiple Choice)

4.9/5

(67)

Question 277

Route congestion and message priority are a few of the functions of what layer of the OSI Model?

(Multiple Choice)

4.7/5

(88)

Question 278

The formula for calculating BTUs from electrical power is:

(Multiple Choice)

4.7/5

(90)

Question 279

What is the MOST important aspect of fire alarm signaling?

(Multiple Choice)

4.9/5

(82)

Question 280

Showing 261 - 280 of 340

Exam 1: BICSI Registered Communications Distribution Designer - RCDD

What type of fiber optic cable is manufactured to protect individual glass strands and is primarily designed for use inside buildings?

Cementitious materials are ________ based materials.

When selecting poles for aerial telecommunications facilities, which of the following is the class number for the strongest rated pole?

When designing a fiber backbone using cable with an armored sheath, a major consideration that you must address is:

One advantage of using preconnectorized jumpers and cables is:

Select the appropriate task to complete the section 2.2 of the work breakdown structure below: 2. Technician 2.1 Install rack 2.2 _________ 2.3 Place fiber 2.4 Terminate fiber 2.5 Test fiber

Which of the following covers lightning protection systems and defines as exposed anything above ground and outside the zone of protection?

A ________ eliminates the need to remove or install materials.

Exhibit: If a work breakdown structure (WBS) shows the tasks below, what is C, the successor task? A) Install OSP pathways B) Install fiber C) ________.

What is the appropriate impedance of coaxial cable for use with broadband distribution?

Color codes for cross-connections fields have been used for many years. Which color is used to identify campus backbone?

What is the MAXIMUM horizontal cable length permitted for centralized optical fiber cabling from the MDA within a data center?

You are placing PTP fiber between two locations 55 km (34 miles) apart. You are told that DWDM equipment will be installed within the next 5 years. Which of the following optical fiber types should you use?

Which of the following is NOT a primary type of DAS antenna?

Within a data center, if you have dual path connectivity between the primary entrance room and secondary entrance room, in addition to dual connectivity between these two rooms and the main distribution and secondary distribution areas, what tier level would this infrastructure design represent?

Route congestion and message priority are a few of the functions of what layer of the OSI Model?

The formula for calculating BTUs from electrical power is:

What is the MOST important aspect of fire alarm signaling?

Filters