Question 1

Which of the following checks evaluates torque converter operation and also checks the transmission for slippage?

Accepted Answer

A)  Cooler flow test 
B)  Air check 
C)  Fluid check 
D)  Stall test 
A)  Cooler flow test 
B)  Air check 
C)  Fluid check 
D)  Stall test

Question 2

Some automatic transmission seals, such as the extension housing seal, may require the replacement of a bushing to properly repair the leak and keep the seal from a repeat failure.

Accepted Answer

A) True 
 B)False

Question 3

Which of the following is heavily loaded during a stall test?

Accepted Answer

A)  Engine 
B)  Transmission 
C)  Brake system 
D)  All of the above 
A)  Engine 
B)  Transmission 
C)  Brake system 
D)  All of the above

Question 4

Tech A says that when checking line pressure, the engine should be off. Tech B says that low line pressure can be caused by a worn pump. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 5

Tire imbalance or tire damage could cause the vehicle to fall when being run on a hoist.

Accepted Answer

A) True 
 B)False

Question 6

After installing leak detection dye in an automatic transmission and running the transmission for a few minutes, any leaking dye should be visible with a black light.

Accepted Answer

A) True 
 B)False

Question 7

Technician A says transmission repairs that can be done without removing the transmission include the replacement of external gaskets and seals. Technician B says transmission repairs that can be done without removing the transmission include the replacement of shift solenoids and repairs to the valve body. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 8

Which of the following can cause an electronic transmission to operate incorrectly?

Accepted Answer

A)  Air leak after the Mass Airflow (MAF) sensor 
B)  Proper fluid type and correct fluid level 
C)  Exhaust system restriction 
D)  Both A and C 
A)  Air leak after the Mass Airflow (MAF) sensor 
B)  Proper fluid type and correct fluid level 
C)  Exhaust system restriction 
D)  Both A and C

Question 9

Which of the following is a method of checking engine and transmission mounts?

Accepted Answer

A)  Prying the engine and transmission to see if the mounts are separated or torn 
B)  Putting the vehicle in gear and applying the brake slowly and check for engine movement 
C)  Putting the vehicle in forward and reverse while slowly applying the throttle and watching for engine movement 
D)  Either A or C 
A)  Prying the engine and transmission to see if the mounts are separated or torn 
B)  Putting the vehicle in gear and applying the brake slowly and check for engine movement 
C)  Putting the vehicle in forward and reverse while slowly applying the throttle and watching for engine movement 
D)  Either A or C

Question 10

High-quality aftermarket and factory scan tools can show live data. Which of the following items can be seen from the data list?

Accepted Answer

A)  Sensor data 
B)  Actuator commands 
C)  DTC's 
D)  Either A nor B 
A)  Sensor data 
B)  Actuator commands 
C)  DTC's 
D)  Either A nor B

Question 11

Hydraulic power train mounts use silicone hydraulic fluid that is squeezed back and forth between three chambers, similar to the design of a shock absorber.

Accepted Answer

A) True 
 B)False

Question 12

Technician A states that whenever possible, you should always test-drive a vehicle to verify the reported problem. Technician B states that before road testing, the transmission fluid level and condition should be checked. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 13

Technician A says powertrain mounts are typically made out of solid steel or aluminum to withstand the power of the engine. Technician B says fluid leaks can cause powertrain mounts to get soft and become faulty. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 14

Technician A says when diagnosing a torque converter clutch (TCC) solenoid problem, you should use a scan tool to identify any diagnostic trouble codes (DTCs) the powertrain control module (PCM) has identified related to the TCC circuit. Technician B says when checking the resistance of the TCC solenoid through the connector and the resistance is out of specifications, the problem could be the solenoid or wires to the solenoid inside the transmission pan. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 15

In which of the following hydraulic circuits will there most likely be a pressure test port?

Accepted Answer

A)  Line pressure circuit 
B)  Torque converter circuit 
C)  3rd Gear circuit 
D)  All of the above 
A)  Line pressure circuit 
B)  Torque converter circuit 
C)  3rd Gear circuit 
D)  All of the above

Question 16

Tech A says that performing a stall test can reveal slippage within the torque converter or transmission. Tech B says that a stall test can damage some transmissions and should not be performed on all transmissions. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 17

The _______ hold the engine and transmission in the proper position in the vehicle.

Accepted Answer

A)  Powertrain mounts 
B)  Suspension hydraulics 
C)  Torsion bar 
D)  Leaf springs 
A)  Powertrain mounts 
B)  Suspension hydraulics 
C)  Torsion bar 
D)  Leaf springs

Question 18

Technician A says that performing a stall test can reveal slipping within the torque converter or transmission. Technician B says that a stall test can damage some transmissions and should not be performed on all transmissions. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 19

If a transmission oil cooler ruptures and leaks, which of the following fluids could contaminate the transmission fluid?

Accepted Answer

A)  Power steering fluid 
B)  Engine coolant 
C)  Transfer case fluid 
D)  Engine oil 
A)  Power steering fluid 
B)  Engine coolant 
C)  Transfer case fluid 
D)  Engine oil

Question 20

Two technicians are discussing electronically controlled automatic transmissions. Technician A says a multimeter is used to pull trouble codes from most vehicles. Technician B says you should follow the diagnostic step by step process until you have completed the diagnostic procedure and found the cause of the diagnostic trouble code (DTC). Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Exam 12: In-Vehicle Transmission Repairs

Which of the following checks evaluates torque converter operation and also checks the transmission for slippage?

Some automatic transmission seals, such as the extension housing seal, may require the replacement of a bushing to properly repair the leak and keep the seal from a repeat failure.

Which of the following is heavily loaded during a stall test?

Tech A says that when checking line pressure, the engine should be off. Tech B says that low line pressure can be caused by a worn pump. Who is correct?

Tire imbalance or tire damage could cause the vehicle to fall when being run on a hoist.

After installing leak detection dye in an automatic transmission and running the transmission for a few minutes, any leaking dye should be visible with a black light.

Which of the following can cause an electronic transmission to operate incorrectly?

Which of the following is a method of checking engine and transmission mounts?

High-quality aftermarket and factory scan tools can show live data. Which of the following items can be seen from the data list?

Hydraulic power train mounts use silicone hydraulic fluid that is squeezed back and forth between three chambers, similar to the design of a shock absorber.

Technician A states that whenever possible, you should always test-drive a vehicle to verify the reported problem. Technician B states that before road testing, the transmission fluid level and condition should be checked. Who is correct?

Technician A says powertrain mounts are typically made out of solid steel or aluminum to withstand the power of the engine. Technician B says fluid leaks can cause powertrain mounts to get soft and become faulty. Who is correct?

In which of the following hydraulic circuits will there most likely be a pressure test port?

Tech A says that performing a stall test can reveal slippage within the torque converter or transmission. Tech B says that a stall test can damage some transmissions and should not be performed on all transmissions. Who is correct?

The _______ hold the engine and transmission in the proper position in the vehicle.

Technician A says that performing a stall test can reveal slipping within the torque converter or transmission. Technician B says that a stall test can damage some transmissions and should not be performed on all transmissions. Who is correct?

If a transmission oil cooler ruptures and leaks, which of the following fluids could contaminate the transmission fluid?

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters