Question 1

Which of the following tests evaluate the transmission pump operation, the pressure regulator function, and the seals and gaskets inside the transmission?

Accepted Answer

A)  Scan tool test 
B)  Hydraulic pressure test 
C)  Fluid level check 
D)  Converter flow check 
A)  Scan tool test 
B)  Hydraulic pressure test 
C)  Fluid level check 
D)  Converter flow check

Question 2

When test driving a vehicle with a scan tool, what can be done to avoid an accident because of distracted driving?

Accepted Answer

A)  Use the scan tool "movie" or "data logger" function 
B)  Place the scan tool on the steering wheel over the airbag to keep it easy to read 
C)  Have an assistant drive the vehicle while you monitor the scan data 
D)  Either A or C 
A)  Use the scan tool "movie" or "data logger" function 
B)  Place the scan tool on the steering wheel over the airbag to keep it easy to read 
C)  Have an assistant drive the vehicle while you monitor the scan data 
D)  Either A or C

Question 3

Technician A states that whenever possible, you should always test-drive a vehicle to verify the reported problem. Technician B states that before road testing, the transmission fluid level and condition should be checked. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 4

The technician should know what the exact problem an automatic transmission has before removing the transmission from the vehicle.

Accepted Answer

A) True 
 B)False

Question 5

Which of the following are steps in a stall test?

Accepted Answer

A)  Apply the park and service brakes fully 
B)  Place the engine in the specified gear 
C)  Run the engine at wide open throttle and record the maximum RPM 
D)  All of the above 
A)  Apply the park and service brakes fully 
B)  Place the engine in the specified gear 
C)  Run the engine at wide open throttle and record the maximum RPM 
D)  All of the above

Question 6

During repair, care must be taken moving heavy parts since automatic transmission fluid is slippery and even after you wipe it off of your hands, a film remains.

Accepted Answer

A) True 
 B)False

Question 7

Typically, a technical service bulletin (TSB) contains which of the following information?

Accepted Answer

A)  Updated programming 
B)  Updated parts 
C)  Updated test procedures 
D)  All of the above 
A)  Updated programming 
B)  Updated parts 
C)  Updated test procedures 
D)  All of the above

Question 8

Which of the following is a common cause low line pressure in a transmission?

Accepted Answer

A)  Weak or worn front pump 
B)  Faulty pressure regulator system 
C)  Internal leaks in the transmission 
D)  All of the above 
A)  Weak or worn front pump 
B)  Faulty pressure regulator system 
C)  Internal leaks in the transmission 
D)  All of the above

Question 9

Which of the following best describes the appearance of clutch material in the bottom of a transmission pan?

Accepted Answer

A)  Sparkly 
B)  Dark residue 
C)  Fine sediment collected on the magnet 
D)  Either A or C 
A)  Sparkly 
B)  Dark residue 
C)  Fine sediment collected on the magnet 
D)  Either A or C

Question 10

Which of the following best describes the appearance of clutch material in the bottom of a transmission pan?

Accepted Answer

A)  Sparkly 
B)  Dark residue 
C)  Fine sediment collected on the magnet 
D)  Either A or C 
A)  Sparkly 
B)  Dark residue 
C)  Fine sediment collected on the magnet 
D)  Either A or C

Question 11

An automatic transmission is heavy and needs to be supported properly with an approved transmission jack while removing it from the vehicle.

Accepted Answer

A) True 
 B)False

Question 12

Most vehicle manufacturers do not recommend stall testing on late-model vehicles, as it can damage the transmission.

Accepted Answer

A) True 
 B)False

Question 13

In order to prevent severe transmission damage, what is the maximum length of time a stall test should be performed?

Accepted Answer

A)  5 seconds 
B)  10 seconds 
C)  15 seconds 
D)  20 seconds 
A)  5 seconds 
B)  10 seconds 
C)  15 seconds 
D)  20 seconds

Question 14

Blocked transmission coolers can starve which of the following transmission circuits?

Accepted Answer

A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit 
A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit

Question 15

Distracted driving can lead to a vehicle accident, so which feature of a scan tool can record the information while you test-drive a vehicle?

Accepted Answer

A)  Freeze-frame 
B)  Movie 
C)  Monitor 
D)  None of the above 
A)  Freeze-frame 
B)  Movie 
C)  Monitor 
D)  None of the above

Question 16

All of the following can be replaced during in-vehicle transmission repairs except:

Accepted Answer

A)  vehicle speed sensor. 
B)  shift solenoids. 
C)  sun gear. 
D)  extension housing bushing. 
A)  vehicle speed sensor. 
B)  shift solenoids. 
C)  sun gear. 
D)  extension housing bushing.

Question 17

When a customer describes a slipping transmission as a complaint, what test is the best way to verify?

Accepted Answer

A)  Fluid test 
B)  Visual inspection 
C)  Road test 
D)  Scan of computer for codes 
A)  Fluid test 
B)  Visual inspection 
C)  Road test 
D)  Scan of computer for codes

Question 18

Which of the following is NOT a method of testing an automatic transmission?

Accepted Answer

A)  Fluid check 
B)  Road test 
C)  Visual inspection 
D)  Shift testing on a hoist 
A)  Fluid check 
B)  Road test 
C)  Visual inspection 
D)  Shift testing on a hoist

Question 19

Technician A says that a knocking noise in the engine/transmission area is typically a bad front pump in the transmission. Technician B says that a knocking noise in the engine/transmission area is more likely to be loose flex plate bolts. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 20

Tech A says that using a scan tool to activate the TCC, with the engine idling in drive and the brakes applied, is a typical troubleshooting task. Tech B says that diagnosis is a waste of time on a faulty transmission because it will be rebuilt anyway. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Exam 12: In-Vehicle Transmission Repairs

Which of the following tests evaluate the transmission pump operation, the pressure regulator function, and the seals and gaskets inside the transmission?

When test driving a vehicle with a scan tool, what can be done to avoid an accident because of distracted driving?

Technician A states that whenever possible, you should always test-drive a vehicle to verify the reported problem. Technician B states that before road testing, the transmission fluid level and condition should be checked. Who is correct?

The technician should know what the exact problem an automatic transmission has before removing the transmission from the vehicle.

Which of the following are steps in a stall test?

During repair, care must be taken moving heavy parts since automatic transmission fluid is slippery and even after you wipe it off of your hands, a film remains.

Typically, a technical service bulletin (TSB) contains which of the following information?

Which of the following is a common cause low line pressure in a transmission?

Which of the following best describes the appearance of clutch material in the bottom of a transmission pan?

Which of the following best describes the appearance of clutch material in the bottom of a transmission pan?

An automatic transmission is heavy and needs to be supported properly with an approved transmission jack while removing it from the vehicle.

Most vehicle manufacturers do not recommend stall testing on late-model vehicles, as it can damage the transmission.

In order to prevent severe transmission damage, what is the maximum length of time a stall test should be performed?

Blocked transmission coolers can starve which of the following transmission circuits?

Distracted driving can lead to a vehicle accident, so which feature of a scan tool can record the information while you test-drive a vehicle?

All of the following can be replaced during in-vehicle transmission repairs except:

When a customer describes a slipping transmission as a complaint, what test is the best way to verify?

Which of the following is NOT a method of testing an automatic transmission?

Technician A says that a knocking noise in the engine/transmission area is typically a bad front pump in the transmission. Technician B says that a knocking noise in the engine/transmission area is more likely to be loose flex plate bolts. Who is correct?

Tech A says that using a scan tool to activate the TCC, with the engine idling in drive and the brakes applied, is a typical troubleshooting task. Tech B says that diagnosis is a waste of time on a faulty transmission because it will be rebuilt anyway. Who is correct?

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters