Question 1

The technician should add fluid to the transmission until it reaches which point dipstick when performing the final checks to an automatic transmission.

Accepted Answer

A)  Safe mark or full mark 
B)  Add mark or safe mark 
C)  Full or over-full mark 
D)  Until it is visible at any point on the dipstick 
A)  Safe mark or full mark 
B)  Add mark or safe mark 
C)  Full or over-full mark 
D)  Until it is visible at any point on the dipstick

Question 2

All of the following statements are true with respect to the bolts and nuts securing the torque converter to the flex plate EXCEPT:

Accepted Answer

A)  All of the engine's power pulses and torque are transmitted through three or four bolts to the torque converter. 
B)  If any bolts are found to be damaged, replace only the damaged bolts. 
C)  If the converter uses nuts, inspect the threads of the studs on the converter for thread damage 
D)  If the studs are damaged, the converter will need to be replaced. 
A)  All of the engine's power pulses and torque are transmitted through three or four bolts to the torque converter. 
B)  If any bolts are found to be damaged, replace only the damaged bolts. 
C)  If the converter uses nuts, inspect the threads of the studs on the converter for thread damage 
D)  If the studs are damaged, the converter will need to be replaced.

Question 3

Blocked transmission coolers can starve which of the following transmission circuits?

Accepted Answer

A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit 
A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit

Question 4

Which of the following should be inspected before reinstalling the transmission?

Accepted Answer

A)  The rear main oil seal 
B)  The engine core plugs 
C)  The engine dowel pins 
D)  All of the above 
A)  The rear main oil seal 
B)  The engine core plugs 
C)  The engine dowel pins 
D)  All of the above

Question 5

Technician A says when installing the torque converter, make sure all three components, oil pump drive, stator support, and turbine input shaft, engage with their mating parts. Technician B says when installing the torque converter, if the torque converter bolts line up with the flex plate holes, you can be sure that it is installed into the transmission properly. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 6

Poor workmanship during the removal and installation of an automatic transmission can result in new transmission problems and reflect poorly on the reputation of the repair shop.

Accepted Answer

A) True 
 B)False

Question 7

Tech A states that transmission coolers must be replaced when replacing or rebuilding the transmission. Tech B states that the transmission cooler must be flushed to clear out debris before installing the new/rebuilt transmission. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 8

Technician A says that the cooler and cooler lines should be flushed as part of a transmission rebuild. Technician B says that if the cooler is not flushed oil returning from the cooler can carry debris into the torque converter, and cause damage to it. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 9

All of the following statements are true with respect to the bolts and nuts securing the torque converter to the flex plate EXCEPT:

Accepted Answer

A)  All of the engine's power pulses and torque are transmitted through three or four bolts to the torque converter. 
B)  If any bolts are found to be damaged, replace only the damaged bolts. 
C)  If the converter uses nuts, inspect the threads of the studs on the converter for thread damage 
D)  If the studs are damaged, the converter will need to be replaced. 
A)  All of the engine's power pulses and torque are transmitted through three or four bolts to the torque converter. 
B)  If any bolts are found to be damaged, replace only the damaged bolts. 
C)  If the converter uses nuts, inspect the threads of the studs on the converter for thread damage 
D)  If the studs are damaged, the converter will need to be replaced.

Question 10

Choose the correct statement with respect to transmission final checks.

Accepted Answer

A)  Many transmissions will require the transmission fluid to be cold before the final check of fluid can be made. 
B)  Do not clear any transmission codes that are in the PCM. 
C)  The fluid level should be checked only after the test drive. 
D)  The longer test drive should run the transmission
through all of the gears. 
A)  Many transmissions will require the transmission fluid to be cold before the final check of fluid can be made. 
B)  Do not clear any transmission codes that are in the PCM. 
C)  The fluid level should be checked only after the test drive. 
D)  The longer test drive should run the transmission
through all of the gears.

Question 11

Technician A says that with the vehicle on the ground, install all of the required amount of transmission fluid before starting the vehicle. Technician B says to add 75% of the required transmission fluid, then start the vehicle and put shifter into each gear before rechecking the fluid level. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 12

Tech A states that by having an assistant step on the brake pedal, the axle nut can easily be torqued. Tech B states that half shafts need to be pushed into the transmission with a dead blow hammer. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 13

Blocked transmission coolers can starve which of the following transmission circuits?

Accepted Answer

A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit 
A)  Torque converter clutch circuit 
B)  Throttle pressure circuit 
C)  Governer pressure circuit 
D)  Transmission lubrication circuit

Question 14

Technician A says that a damaged flex plate can cause knocking noises and damage to the front pump of the transmission. Technician B says that all of the engine power pulses and torque are transmitted through the bolts or studs holding the automatic transmission's torque converter to the flex plate. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 15

Transmission coolers can be cleaned by:

Accepted Answer

A)  an aerosol flushing kit. 
B)  compressed air. 
C)  detergents. 
D)  rust inhibitors. 
A)  an aerosol flushing kit. 
B)  compressed air. 
C)  detergents. 
D)  rust inhibitors.

Question 16

It is a good practice to have a customer return in a few hundred miles for a reinspection.

Accepted Answer

A) True 
 B)False

Question 17

Using an impact gun to tighten up the axle retaining nut will:

Accepted Answer

A)  ensure proper fit. 
B)  cause the bearing to have too much preload. 
C)  ensure that torque of the correct specification is applied. 
D)  prevent the axle from spinning while you torque the nut. 
A)  ensure proper fit. 
B)  cause the bearing to have too much preload. 
C)  ensure that torque of the correct specification is applied. 
D)  prevent the axle from spinning while you torque the nut.

Question 18

Technician A says some vehicles are equipped with a dust cover that needs to be removed to access the bolts connecting the torque converter to the flex plate. Technician B says when removing a transmission, there is no need to plug the transmission cooler lines and transmission vent hose. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 19

What precaution could be taken when reinstalling a half shaft if your area uses excessive amounts of road salt in the winter?

Accepted Answer

A)  Apply petroleum jelly to the outer layer of the half shaft 
B)  Apply a thick coating of enamel paint to the outer surface of the half shaft 
C)  Apply a small amount of grease or anti-seize to the outer splines of the half shaft 
D)  Fix an outer plastic covering to prevent contact with the salt 
A)  Apply petroleum jelly to the outer layer of the half shaft 
B)  Apply a thick coating of enamel paint to the outer surface of the half shaft 
C)  Apply a small amount of grease or anti-seize to the outer splines of the half shaft 
D)  Fix an outer plastic covering to prevent contact with the salt

Question 20

When installing a transmission in a front-wheel drive:

Accepted Answer

A)  use the bolts to pull the transmission into place on the engine. 
B)  with the transmission seated against the engine, tighten the bolts as and when they are installed. 
C)  install the half shafts before removing the engine support bar. 
D)  lubricate the circlip with a small amount of transmission assembly lubricant or petroleum jelly. 
A)  use the bolts to pull the transmission into place on the engine. 
B)  with the transmission seated against the engine, tighten the bolts as and when they are installed. 
C)  install the half shafts before removing the engine support bar. 
D)  lubricate the circlip with a small amount of transmission assembly lubricant or petroleum jelly.

Exam 19: Transmission Reinstallation

The technician should add fluid to the transmission until it reaches which point dipstick when performing the final checks to an automatic transmission.

All of the following statements are true with respect to the bolts and nuts securing the torque converter to the flex plate EXCEPT:

Blocked transmission coolers can starve which of the following transmission circuits?

Which of the following should be inspected before reinstalling the transmission?

Poor workmanship during the removal and installation of an automatic transmission can result in new transmission problems and reflect poorly on the reputation of the repair shop.

Tech A states that transmission coolers must be replaced when replacing or rebuilding the transmission. Tech B states that the transmission cooler must be flushed to clear out debris before installing the new/rebuilt transmission. Who is correct?

Technician A says that the cooler and cooler lines should be flushed as part of a transmission rebuild. Technician B says that if the cooler is not flushed oil returning from the cooler can carry debris into the torque converter, and cause damage to it. Who is correct?

All of the following statements are true with respect to the bolts and nuts securing the torque converter to the flex plate EXCEPT:

Choose the correct statement with respect to transmission final checks.

Tech A states that by having an assistant step on the brake pedal, the axle nut can easily be torqued. Tech B states that half shafts need to be pushed into the transmission with a dead blow hammer. Who is correct?

Blocked transmission coolers can starve which of the following transmission circuits?

Transmission coolers can be cleaned by:

It is a good practice to have a customer return in a few hundred miles for a reinspection.

Using an impact gun to tighten up the axle retaining nut will:

What precaution could be taken when reinstalling a half shaft if your area uses excessive amounts of road salt in the winter?

When installing a transmission in a front-wheel drive:

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Transmission Components

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters