Question 1

The __________ is the component that will deliver the torque from the transmission to either the driveshaft or the axle shafts.

Accepted Answer

A)  stator 
B)  input shaft 
C)  turbine 
D)  output shaft 
A)  stator 
B)  input shaft 
C)  turbine 
D)  output shaft

Question 2

When rebuilding the transmission, the valve body should be serviced or replaced.

Accepted Answer

A) True 
 B)False

Question 3

What part can directly drive the front pump of an automatic transmission?

Accepted Answer

A)  Torque converter 
B)  Flywheel 
C)  Transmission input shaft 
D)  Transmission output shaft 
A)  Torque converter 
B)  Flywheel 
C)  Transmission input shaft 
D)  Transmission output shaft

Question 4

Which of the following provides input shaft speed data to the Powertrain Control Module (PCM)?

Accepted Answer

A)  Vehicle speed sensor 
B)  Turbine speed sensor 
C)  Output shaft speed sensor 
D)  Impeller speed sensor 
A)  Vehicle speed sensor 
B)  Turbine speed sensor 
C)  Output shaft speed sensor 
D)  Impeller speed sensor

Question 5

Which of these sensors cannot be used to determine engine speed?

Accepted Answer

A)  Vehicle Speed Sensor (VSS) 
B)  Crankshaft Position Sensor (CKP) 
C)  Input Shaft Speed Sensor (ISS) 
D)  Either A and C 
A)  Vehicle Speed Sensor (VSS) 
B)  Crankshaft Position Sensor (CKP) 
C)  Input Shaft Speed Sensor (ISS) 
D)  Either A and C

Question 6

Which of the following statements is NOT true regarding the transmission pan?

Accepted Answer

A)  Made of aluminum or steel 
B)  Contains the filter 
C)  May contain the valve body 
D)  Is not removeable 
A)  Made of aluminum or steel 
B)  Contains the filter 
C)  May contain the valve body 
D)  Is not removeable

Question 7

Tech A states that bushings should be checked for wear during an overhaul and replaced if needed. Tech B states that ALL bushings should be replaced during an overhaul. Who is correct?

Accepted Answer

A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B 
A)  Tech A 
B)  Tech B 
C)  Both A and B 
D)  Neither A nor B

Question 8

Technician A says that the valve body on a rear wheel drive vehicle may be found in the lower transmission pan. Technician B says that the valve body on a front wheel drive vehicle may be found behind the side transmission pan. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 9

Technician A says that when rebuilding an automatic transmission, the valve body requires no special service. Technician B says that when rebuilding an automatic transmission, the valve body never needs to be replaced. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician 
A)  Technician A 
B)  Technician B 
C)  Both technicians 
D)  Neither technician

Question 10

Technician A says the manual lever position (MLP) switch is sometimes called a transmission range switch or a neutral safety switch. Technician B says a MLP switch is a multi-position switch that sends a signal to the power train control module (PCM) regarding which gear the manual lever is in. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 11

Technician A says thrust washers are a friction type of bearing. Technician B says thrust bearings are a type of flat needle roller bearing. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 12

Which of the following can be found in a valve body?

Accepted Answer

A)  Check valves 
B)  Orifices 
C)  Spool valve 
D)  All of the above 
A)  Check valves 
B)  Orifices 
C)  Spool valve 
D)  All of the above

Question 13

Technician A says the manual lever position (MLP) switch is sometimes called a transmission range switch or a neutral safety switch. Technician B says a MLP switch monitors transmission fluid levels. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 14

Technician A says on computerized transmissions, an electronic pressure control (EPsolenoid is used to regulate transmission line pressure. Technician B says most EPC solenoids are pulse-width modulated. Who is correct?

Accepted Answer

A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B 
A)  Technician A 
B)  Technician B 
C)  Both A and B 
D)  Neither A nor B

Question 15

Which of these materials is least likely to be used as a servo piston seal?

Accepted Answer

A)  Neoprene 
B)  Teflon 
C)  Aluminum 
D)  None of the above 
A)  Neoprene 
B)  Teflon 
C)  Aluminum 
D)  None of the above

Question 16

A transmission fluid warmer is used to warm up the fluid quickly.

Accepted Answer

A) True 
 B)False

Question 17

A transmission painted a particular color indicates which of the following?

Accepted Answer

A)  Identifies that the transmission was rebuilt 
B)  Helps seal the transmission after being cleaned 
C)  Both A and B 
D)  Neither A nor B 
A)  Identifies that the transmission was rebuilt 
B)  Helps seal the transmission after being cleaned 
C)  Both A and B 
D)  Neither A nor B

Question 18

Which pump design produces the same amount of flow with each pump shaft rotation?

Accepted Answer

A)  Negative displacement 
B)  Vane displacement 
C)  Positive displacement 
D)  Variable displacement 
A)  Negative displacement 
B)  Vane displacement 
C)  Positive displacement 
D)  Variable displacement

Question 19

Choose the correct statement.

Accepted Answer

A)  Drums or shells are not a part of the spinning assembly. 
B)  Planetary gears and sun gear are mounted outside of a drum. 
C)  The drum is splined to the sun gear, ring gear, or the planet carrier. 
D)  If the drum contains a multiple disc clutch in it, it is called a shell. 
A)  Drums or shells are not a part of the spinning assembly. 
B)  Planetary gears and sun gear are mounted outside of a drum. 
C)  The drum is splined to the sun gear, ring gear, or the planet carrier. 
D)  If the drum contains a multiple disc clutch in it, it is called a shell.

Question 20

Which of the following is a common name for the primary automatic transmission oil pump?

Accepted Answer

A)  The rear pump 
B)  The main pump 
C)  The drive pump 
D)  The front pump 
A)  The rear pump 
B)  The main pump 
C)  The drive pump 
D)  The front pump

Exam 7: Transmission Components

The __________ is the component that will deliver the torque from the transmission to either the driveshaft or the axle shafts.

When rebuilding the transmission, the valve body should be serviced or replaced.

What part can directly drive the front pump of an automatic transmission?

Which of the following provides input shaft speed data to the Powertrain Control Module (PCM)?

Which of these sensors cannot be used to determine engine speed?

Which of the following statements is NOT true regarding the transmission pan?

Tech A states that bushings should be checked for wear during an overhaul and replaced if needed. Tech B states that ALL bushings should be replaced during an overhaul. Who is correct?

Technician A says that the valve body on a rear wheel drive vehicle may be found in the lower transmission pan. Technician B says that the valve body on a front wheel drive vehicle may be found behind the side transmission pan. Who is correct?

Technician A says that when rebuilding an automatic transmission, the valve body requires no special service. Technician B says that when rebuilding an automatic transmission, the valve body never needs to be replaced. Who is correct?

Technician A says thrust washers are a friction type of bearing. Technician B says thrust bearings are a type of flat needle roller bearing. Who is correct?

Which of the following can be found in a valve body?

Technician A says the manual lever position (MLP) switch is sometimes called a transmission range switch or a neutral safety switch. Technician B says a MLP switch monitors transmission fluid levels. Who is correct?

Technician A says on computerized transmissions, an electronic pressure control (EPsolenoid is used to regulate transmission line pressure. Technician B says most EPC solenoids are pulse-width modulated. Who is correct?

Which of these materials is least likely to be used as a servo piston seal?

A transmission fluid warmer is used to warm up the fluid quickly.

A transmission painted a particular color indicates which of the following?

Which pump design produces the same amount of flow with each pump shaft rotation?

Choose the correct statement.

Which of the following is a common name for the primary automatic transmission oil pump?

Strategy-Based Diagnostics

Safety

Basic Tools and Precision Measuring

Fasteners and Thread Repair

Vehicle, Customer, and Service Information

Automatic Transmission Fundamentals

Hydraulic Fundamentals

Torque Converter Principles

Hydraulically Controlled Transmission

Electronically Controlled Transmission

In-Vehicle Transmission Repairs

Transmission Removal

Transmission Disassembly

Hydraulic System Rebuilding

Gear Train Rebuilding

Valve Body and Electric Service

Transmission Reassembly

Transmission Reinstallation

Dual Clutch Transmissions

Continuously Variable Transmissions

Hybrid Transmissions

Honda Transmissions

Chrysler 6 Speed 62te Transmission

6t40 6f35 Transmission

Zf 9hp Chrysler 948te Transmission

Ford 6r60 Zf6hp26

Allison 1000 and 2000 Series Transmissions

Filters