Question 1

Describe the steps that should be performed prior to flashing the BCM.

Accepted Answer

Check the condition of the vehicle's battery. 
 a. Connect a battery charger and maintain a constant 12 volts at the battery throughout the reprogramming procedure. 
 b. Use a dedicated computer. 
 c. Have a subscription. 
 d. D etermine if the control module actually requires a calibration update.

Question 2

The NOT gate reverses binary code.

Accepted Answer

A) True 
 B)False  True

Question 3

A transistor that operates as a relay is the basis of the ____ computer.

Accepted Answer

A)  analog 
B)  binary 
C)  interface 
D)  digital 
A)  analog 
B)  binary 
C)  interface 
D)  digital D

Question 4

Explain the function of a multiplexor.

Accepted Answer

It is used to examin

Question 5

The ____ is the brain of the computer.

Accepted Answer

A)  microprocessor 
B)  A/D converter 
C)  program 
D)  interface circuit 
A)  microprocessor 
B)  A/D converter 
C)  program 
D)  interface circuit

Question 6

A stepper motor may have two or four field coils.

Accepted Answer

A) True 
 B)False

Question 7

If a malfunction results in improper system operation, the computer may minimize the effects by using ____ action.

Accepted Answer

A)  by-pass 
B)  breaking 
C)  shut down 
D)  fail-safe 
A)  by-pass 
B)  breaking 
C)  shut down 
D)  fail-safe

Question 8

List the precautions necessary to prevent static electricity damage when replacing a control module.

Accepted Answer

a. Ground yourself and the package to a

Question 9

Most computer-controlled actuators are ____ that convert the output commands from the computer into mechanical action.

Accepted Answer

A)  electromechanical devices 
B)  switches 
C)  sensors 
D)  valves 
A)  electromechanical devices 
B)  switches 
C)  sensors 
D)  valves

Question 10

High resistance in the sensor return circuit can cause a faulty input from all sensors that use a shared circuit.

Accepted Answer

A) True 
 B)False

Question 11

Flashing a BCM is being discussed. Technician A says a battery charger must be connected to maintain 12 volts during the entire flash procedure. Technician B says that most reprogramming procedures can be reverted to the original programming. Who is correct?

Accepted Answer

A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B 
A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B

Question 12

Technician A says that a PWM actuator cannot be tested with a DMM. Technician B says the PWM actuator may be tested with a lab scope. Who is correct?

Accepted Answer

A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B 
A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B

Question 13

Technician A says when servicing the BCM, a test light should be used to check for voltage. Technician B says before making or breaking electrical connections to the BCM, make sure the ignition switch is off. Who is correct?

Accepted Answer

A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B 
A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B

Question 14

What component contains specific data that pertains to the exact vehicle in which the computer is installed?

Accepted Answer

The answer of What component contains specific data that pertains...

Question 15

Technician A says the microprocessor commands actuators by output drivers. Technician B says that outputs are never controlled by supplying voltage to the actuator. Who is correct?

Accepted Answer

A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B 
A)  Technician A only 
B)  Technician B only 
C)  Both Technician A and B 
D)  Neither Technician A nor B

Question 16

A stepper motor contains a permanent magnet armature.

Accepted Answer

A) True 
 B)False

Question 17

What is the purpose of the interface.

Accepted Answer

An interface is used to protect the comp

Question 18

The operation of a computer is divided into four basic functions: ____.

Accepted Answer

A)  Addition, Subtraction, Multiplication, Division 
B)  Sequence, Selection, Repetition, Output 
C)  Input, Processing, Storage, Output 
D)  Audio, Video, Calculate, Store 
A)  Addition, Subtraction, Multiplication, Division 
B)  Sequence, Selection, Repetition, Output 
C)  Input, Processing, Storage, Output 
D)  Audio, Video, Calculate, Store

Question 19

A(n) ____ is a microprocessor designed to communicate with the BCM.

Accepted Answer

A)  actuator 
B)  scan tool 
C)  sensor 
D)  reader 
A)  actuator 
B)  scan tool 
C)  sensor 
D)  reader

Question 20

Name the components that should be visually inspected before attempting to test the BCM-controlled system.

Accepted Answer

All sensors, electri

Describe the steps that should be performed prior to flashing the BCM.

The NOT gate reverses binary code.

A transistor that operates as a relay is the basis of the ____ computer.

Explain the function of a multiplexor.

The ____ is the brain of the computer.

A stepper motor may have two or four field coils.

If a malfunction results in improper system operation, the computer may minimize the effects by using ____ action.

List the precautions necessary to prevent static electricity damage when replacing a control module.

Most computer-controlled actuators are ____ that convert the output commands from the computer into mechanical action.

High resistance in the sensor return circuit can cause a faulty input from all sensors that use a shared circuit.

Flashing a BCM is being discussed. Technician A says a battery charger must be connected to maintain 12 volts during the entire flash procedure. Technician B says that most reprogramming procedures can be reverted to the original programming. Who is correct?

Technician A says that a PWM actuator cannot be tested with a DMM. Technician B says the PWM actuator may be tested with a lab scope. Who is correct?

Technician A says when servicing the BCM, a test light should be used to check for voltage. Technician B says before making or breaking electrical connections to the BCM, make sure the ignition switch is off. Who is correct?

What component contains specific data that pertains to the exact vehicle in which the computer is installed?

Technician A says the microprocessor commands actuators by output drivers. Technician B says that outputs are never controlled by supplying voltage to the actuator. Who is correct?

A stepper motor contains a permanent magnet armature.

What is the purpose of the interface.

The operation of a computer is divided into four basic functions: ____.

A(n) ____ is a microprocessor designed to communicate with the BCM.

Name the components that should be visually inspected before attempting to test the BCM-controlled system.

Introduction to Automotive Electrical and Electronic Systems Safety

Basic Theoriesspecial Tools and Procedures

Electrical and Electronic Componentsbasic Electrical Troubleshooting and Service

Wiring and Circuit Diagramswiring Repair and Reading Circuit Diagrams

Automotive Batteriesbattery Diagnosis and Service

Starting Systems and Motor Designsstarting System Diagnosis and Service

Charging Systemscharging System Testing and Service

Computer Inputssensor Diagnostic Routines

Vehicle Communication Networksvehicle Multiplexing Diagnostics

Lighting Circuitslighting Circuits Repair and Diagnosis

Instrumentation and Warning Lampsinstrumentation and Warning Lamp System Diagnosis and Repair

Accessorieselectrical Accessories Diagnosis and Repair

Radio Frequency and Infotainment Systemsservicing Radio Frequency and Infotainment Systems

Passive Restraint and Vehicle Safety Systemsservicing Passive Restraint and Vehicle Safety Systems

Vehicles With Alternative Power Sourceshybrid and High-Voltage System Service

Filters

Exam 8: Introduction to the Body Computerbody Computer System Diagnosis

Describe the steps that should be performed prior to flashing the BCM.

The NOT gate reverses binary code.

A transistor that operates as a relay is the basis of the ____ computer.

Explain the function of a multiplexor.

The ____ is the brain of the computer.

A stepper motor may have two or four field coils.

If a malfunction results in improper system operation, the computer may minimize the effects by using ____ action.

List the precautions necessary to prevent static electricity damage when replacing a control module.

Most computer-controlled actuators are ____ that convert the output commands from the computer into mechanical action.

High resistance in the sensor return circuit can cause a faulty input from all sensors that use a shared circuit.

Flashing a BCM is being discussed. Technician A says a battery charger must be connected to maintain 12 volts during the entire flash procedure. Technician B says that most reprogramming procedures can be reverted to the original programming. Who is correct?

Technician A says that a PWM actuator cannot be tested with a DMM. Technician B says the PWM actuator may be tested with a lab scope. Who is correct?

Technician A says when servicing the BCM, a test light should be used to check for voltage. Technician B says before making or breaking electrical connections to the BCM, make sure the ignition switch is off. Who is correct?

What component contains specific data that pertains to the exact vehicle in which the computer is installed?

Technician A says the microprocessor commands actuators by output drivers. Technician B says that outputs are never controlled by supplying voltage to the actuator. Who is correct?

A stepper motor contains a permanent magnet armature.

What is the purpose of the interface.

The operation of a computer is divided into four basic functions: ____.

A(n) ____ is a microprocessor designed to communicate with the BCM.

Name the components that should be visually inspected before attempting to test the BCM-controlled system.

Introduction to Automotive Electrical and Electronic Systems Safety

Basic Theoriesspecial Tools and Procedures

Electrical and Electronic Componentsbasic Electrical Troubleshooting and Service

Wiring and Circuit Diagramswiring Repair and Reading Circuit Diagrams

Automotive Batteriesbattery Diagnosis and Service

Starting Systems and Motor Designsstarting System Diagnosis and Service

Charging Systemscharging System Testing and Service

Computer Inputssensor Diagnostic Routines

Vehicle Communication Networksvehicle Multiplexing Diagnostics

Lighting Circuitslighting Circuits Repair and Diagnosis

Instrumentation and Warning Lampsinstrumentation and Warning Lamp System Diagnosis and Repair

Accessorieselectrical Accessories Diagnosis and Repair

Radio Frequency and Infotainment Systemsservicing Radio Frequency and Infotainment Systems

Passive Restraint and Vehicle Safety Systemsservicing Passive Restraint and Vehicle Safety Systems

Vehicles With Alternative Power Sourceshybrid and High-Voltage System Service

Filters