Question 1

The ____________________ is the space created as material is removed during a cut.

Accepted Answer

The answer of The ____________________ is the space created as...

Question 2

​What is the term use to identify anything that was created primarily by welding?

Accepted Answer

A)  ​fabrication 
B)  ​welded structure 
C)  ​weldment 
D)  ​assembly 
A)  ​fabrication 
B)  ​welded structure 
C)  ​weldment 
D)  ​assembly

Question 3

____ is/are usually 3/16 in.(4.7 mm) or less and measured in gauge or decimals of an inch.

Accepted Answer

A)  Sheets 
B)  Plates 
C)  Pipes 
D)  Tubing 
A)  Sheets 
B)  Plates 
C)  Pipes 
D)  Tubing

Question 4

The opposite end of the spectrum from preformed parts is ____________________ in which all or most of the assembly is handmade.

Accepted Answer

The answer of The opposite end of the spectrum from...

Question 5

____ are useful for clamping larger parts.These clamps have a sliding lower jaw that can be positioned against the part before tightening the screw-clamping end.

Accepted Answer

A)  Pipe clamps 
B)  Cam-lock clamps 
C)  Bar clamps 
D)  C-clamps 
A)  Pipe clamps 
B)  Cam-lock clamps 
C)  Bar clamps 
D)  C-clamps

Question 6

​What should be a concern as a weldment becomes larger as more parts are added?

Accepted Answer

A)  ​That it is well supported so it does not fall. 
B)  ​That it does not get too tall and the top cannot be reached by using a ladder. 
C)  ​That you will have to stand on part of the weldment to reach the other parts to weld them. 
D)  ​It may be too large to see over. 
A)  ​That it is well supported so it does not fall. 
B)  ​That it does not get too tall and the top cannot be reached by using a ladder. 
C)  ​That you will have to stand on part of the weldment to reach the other parts to weld them. 
D)  ​It may be too large to see over.

Question 7

____ clamps are very similar to bar clamps.The advantage of these clamps is that the ends can be attached to a section of standard 1/2-in.(13 mm) pipe.

Accepted Answer

A)  Specialty 
B)  Bar 
C)  Cam-lock 
D)  Pipe 
A)  Specialty 
B)  Bar 
C)  Cam-lock 
D)  Pipe

Question 8

​What is the term used to describe the process of bringing together all of the parts for a weldment?

Accepted Answer

A)  ​assembly 
B)  ​fabrication 
C)  ​part requisition 
D)  ​bill-of-materials listing 
A)  ​assembly 
B)  ​fabrication 
C)  ​part requisition 
D)  ​bill-of-materials listing

Question 9

What should you do if you are going to be welding around other workers who are not welders?

Accepted Answer

A)  Tell them about the sparks. 
B)  Tell them about the arc light. 
C)  Tell them of other hazards. 
D)  All of the above 
A)  Tell them about the sparks. 
B)  Tell them about the arc light. 
C)  Tell them of other hazards. 
D)  All of the above

Question 10

____ are dimensioned by giving the length of their legs and their thickness.

Accepted Answer

A)  Angles 
B)  Sheets 
C)  Pipes 
D)  Plates 
A)  Angles 
B)  Sheets 
C)  Pipes 
D)  Plates

Question 11

____, such as those for pipe welding, are available for many different types of jobs.Such clamps make it possible to do faster and more accurate assembling.

Accepted Answer

A)  Bar clamps 
B)  Pipe clamps 
C)  C-clamps 
D)  Specialty clamps 
A)  Bar clamps 
B)  Pipe clamps 
C)  C-clamps 
D)  Specialty clamps

Question 12

​One advantage of tools like the ____ is that all sides of a cut in structural shapes and pipe can be laid out from one side without relocating the tool.

Accepted Answer

A)  ​pipe clamp 
B)  ​contour marker 
C)  ​template 
D)  ​metal scribe 
A)  ​pipe clamp 
B)  ​contour marker 
C)  ​template 
D)  ​metal scribe

Exam 23: Fabricating Techniques and Practices

The ____________________ is the space created as material is removed during a cut.

​What is the term use to identify anything that was created primarily by welding?

____ is/are usually 3/16 in.(4.7 mm) or less and measured in gauge or decimals of an inch.

The opposite end of the spectrum from preformed parts is ____________________ in which all or most of the assembly is handmade.

____ are useful for clamping larger parts.These clamps have a sliding lower jaw that can be positioned against the part before tightening the screw-clamping end.

​What should be a concern as a weldment becomes larger as more parts are added?

____ clamps are very similar to bar clamps.The advantage of these clamps is that the ends can be attached to a section of standard 1/2-in.(13 mm) pipe.

​What is the term used to describe the process of bringing together all of the parts for a weldment?

What should you do if you are going to be welding around other workers who are not welders?

____ are dimensioned by giving the length of their legs and their thickness.

____, such as those for pipe welding, are available for many different types of jobs.Such clamps make it possible to do faster and more accurate assembling.

​One advantage of tools like the ____ is that all sides of a cut in structural shapes and pipe can be laid out from one side without relocating the tool.

Introduction to Welding

Safety in Welding

Shielded Metal Arc Equipment, Setup, and Operation

Shielded Metal Arc Welding of Plate

Shielded Metal Arc Welding of Pipe

Shielded Metal Arc Welding Aws Sense Certification

Flame Cutting

Plasma Arc Cutting

Related Cutting Processes

Gas Metal Arc Welding Equipment, Setup, and Operation

Gas Metal Arc Welding

Flux Cored Arc Welding Equipment, Setup, and Operation

Flux Cored Arc Welding

Gas Metal Arc and Flux Cored Arc Welding of Pipe

Gas Metal Arc and Flux Cored Arc Welding Aws Sense Certification

Gas Tungsten Arc Welding Equipment, Setup, Operation, and Filler Metals

Gas Tungsten Arc Welding of Plate

Gas Tungsten Arc Welding of Pipe

Gas Tungsten Arc Welding Plate and Pipe Aws Sense Certification

Shop Math and Weld Cost

Reading Technical Drawings

Welding Joint Design and Welding Symbols

Welding Codes and Standards

Testing and Inspection of Welds

Welding Metallurgy

Weldability of Metals

Filler Metal Selection

Welding Automation and Robotics

Other Welding Processes

Oxyfuel Welding and Cutting Equipment, Setup, and Operation

Oxyacetylene Welding

Brazing, Braze Welding, and Soldering

Filters

What is the term use to identify anything that was created primarily by welding?

What should be a concern as a weldment becomes larger as more parts are added?

What is the term used to describe the process of bringing together all of the parts for a weldment?

One advantage of tools like the ____ is that all sides of a cut in structural shapes and pipe can be laid out from one side without relocating the tool.