Question 1

Identify the transmission fluid level for a fluid temperature of 191 degree Fahrenheit.

Accepted Answer

A)   34-46 mm
B)   25-32 mm
C)   15-25 mm
D)   48-54 mm A

Question 2

You are rebuilding a 62TE transmission. You test the overdrive solenoid and find the resistance is 5 ohms. Tech A states that the overdrive solenoid is within specification. Tech B states that the entire solenoid pack will need to be replaced. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A nor B B

Question 3

Tech A states that the 62TE transmission design is based upon the 41TE transmission. Tech B states that 62TE transmission design is based upon the 42RLE transmission. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A and B A

Question 4

Technician A says that there are five pressure switches built into the solenoid body assembly that are monitored by the PCM to verify correct clutches are applied. Technician B says that the five pressure solenoids are supplied 12 volts and should have a resistance of 300 ohms with pressure applied to them. Who is correct?

Accepted Answer

A)   Technician A
B)   Technician B
C)   Both technicians
D)   Neither technician

Question 5

A vehicle comes into the shop with a customer complaint of transmission performance problems and the MIL is illuminated. You drive the vehicle and determine that the transmission does not have 1st, 3rd or 4th gear. You scan the vehicle and find codes related to ratio errors for 1st, 3rd, and 4th gear. Tech A states that the problem could be the low clutch. Tech B states that the problem could be the sprag. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A nor B

Question 6

When using an old speedometer cable to check the transmission fluid level of 62TE, a paint marker should be used to mark a line at ________ from the end of the cable.

Accepted Answer

A)   8.120 inches
B)   10.340 inches
C)   25.180 inches
D)   16.690 inches

Question 7

Choose the correct statement with respect to solenoids in the 62TE transmission.

Accepted Answer

A)   The clutch solenoids operate a shuttle valve.
B)   In 3rd gear, the underdrive clutch solenoid and the 2-4 clutch solenoid will allow fluid flow to their respective clutches.
C)   The solenoids can be tested directly.
D)   The solenoids can be replaced individually.

Question 8

When installing new sealing rings onto the low clutch housing, the entire housing must be replaced if the amount of clearance between the sealing ring and the groove is more than:

Accepted Answer

A)   0.1 inch (2.54 mm) .
B)   0.1 mm (0.004 in) .
C)   0.01 inch (0.25 mm) .
D)   0.01 mm (0.0004 in) .

Question 9

Technician A says that the 62TE transmission utilizes a double swap shift. Technician B says that the sensors in the transmission are used to determine any gear ratio errors. Who is correct?

Accepted Answer

A)   Technician A
B)   Technician B
C)   Both technicians
D)   Neither technician

Question 10

The temperature of the transmission will affect the level displayed on the indicator.

Accepted Answer

A) True 
 B)False

Question 11

Identify the component of 62TE transmission shown in the given figure

Accepted Answer

A)   Variable force solenoid
B)   Transmission case
C)   Hex-style plug
D)   Transfer shaft

Question 12

The speed sensors can be used to determine any ratio errors inside the transmission. Ratio errors generally mean:

Accepted Answer

A)   fault in the crankshaft position sensor.
B)   worn-out belt.
C)   clutch or sprag is slipping.
D)   piston wear.

Question 13

When rebuilding the transmission case, the retaining bolts of the pinion gear cover should be torqued to:

Accepted Answer

A)   2 to 8 in-lb (0.23-0.90 N·m) .
B)   45 ft-lb (61.01 N·m) .
C)   200 ft-lb (271.16 N·m) .
D)   105 in-lb (11.86 N·m) .

Question 14

Technician A says that the 62TE transmission uses a transmission range switch with four separate switches that identify the current gear selected by the driver. Technician B says that these switches will either be open or closed. Who is correct?

Accepted Answer

A)   Technician A
B)   Technician B
C)   Both technicians
D)   Neither technician

Question 15

A three-wire line pressure sensor is used to send pressure voltages to the BCM.

Accepted Answer

A) True 
 B)False

Question 16

Technician A says that the 62TE transmission has seven forward gear ratios. Technician B says that the seventh forward gear is used to make a smooth downshift from the sixth gear at highway speeds. Who is correct?

Accepted Answer

A)   Technician A
B)   Technician B
C)   Both technicians
D)   Neither technician

Question 17

You have a vehicle come in with a complaint of harsh shifting. You measure line pressure and find that it is high. You look at the scan tool and find that the pressure control solenoid is commanded to 62%. Tech A states that the TCM is commanding the transmission to maximum line pressure. Tech B states that the TCM is commanding 62% of line pressure. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A nor B

Question 18

A 62TE transmission reassembly is being discussed. Technician A says that all the washers on the front pump screws should be replaced before installation. Technician B says that the dipstick stop should be installed at the same time as a new filter. Who is correct?

Accepted Answer

A)   Technician A
B)   Technician B
C)   Both Technicians A and B
D)   Neither Technician A nor B

Question 19

A vehicle comes into the shop with soft shifts. You measure line pressure and find that the line pressure is low. You check the voltage coming out of the transmission pressure sensor and find that it is 5 volts. Tech A states that the vehicle has a problem with the line pressure sensor. Tech B states that the vehicle needs a new pump or line pressure solenoid. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A nor B

Question 20

A vehicle comes in with a transmission that is slipping. You check the temperature of the transmission using a scan tool and find that it is 191 degrees F. You measure the fluid level and find it is 32 mm. Tech A states that the fluid level is low. Tech B states that the fluid level is too high. Who is correct?

Accepted Answer

A)   Tech A
B)   Tech B
C)   Both A and B
D)   Neither A nor B

Exam 24: Chrysler 6 Speed 62te Transmission

Identify the transmission fluid level for a fluid temperature of 191 degree Fahrenheit.

You are rebuilding a 62TE transmission. You test the overdrive solenoid and find the resistance is 5 ohms. Tech A states that the overdrive solenoid is within specification. Tech B states that the entire solenoid pack will need to be replaced. Who is correct?

Tech A states that the 62TE transmission design is based upon the 41TE transmission. Tech B states that 62TE transmission design is based upon the 42RLE transmission. Who is correct?

When using an old speedometer cable to check the transmission fluid level of 62TE, a paint marker should be used to mark a line at ________ from the end of the cable.

Choose the correct statement with respect to solenoids in the 62TE transmission.

When installing new sealing rings onto the low clutch housing, the entire housing must be replaced if the amount of clearance between the sealing ring and the groove is more than:

Technician A says that the 62TE transmission utilizes a double swap shift. Technician B says that the sensors in the transmission are used to determine any gear ratio errors. Who is correct?

The temperature of the transmission will affect the level displayed on the indicator.

Identify the component of 62TE transmission shown in the given figure

The speed sensors can be used to determine any ratio errors inside the transmission. Ratio errors generally mean:

When rebuilding the transmission case, the retaining bolts of the pinion gear cover should be torqued to:

Technician A says that the 62TE transmission uses a transmission range switch with four separate switches that identify the current gear selected by the driver. Technician B says that these switches will either be open or closed. Who is correct?

A three-wire line pressure sensor is used to send pressure voltages to the BCM.

Technician A says that the 62TE transmission has seven forward gear ratios. Technician B says that the seventh forward gear is used to make a smooth downshift from the sixth gear at highway speeds. Who is correct?

A 62TE transmission reassembly is being discussed. Technician A says that all the washers on the front pump screws should be replaced before installation. Technician B says that the dipstick stop should be installed at the same time as a new filter. Who is correct?