Question 1

True position is the theoretically exact location ____ of a feature.

Accepted Answer

A)  of the datum 
B)  of the axis 
C)  of the center plane 
D)  both b and c 
E)  all of the above 
A)  of the datum 
B)  of the axis 
C)  of the center plane 
D)  both b and c 
E)  all of the above

Question 2

All three material condition modifying elements have specific symbols associated with them.

Accepted Answer

A) True 
 B)False

Question 3

"FIM" is an acronym for ____.

Accepted Answer

A)  feature indication maximum 
B)  form illustration maximum 
C)  full indicator movement 
D)  form indicator movement 
E)  none of the above 
A)  feature indication maximum 
B)  form illustration maximum 
C)  full indicator movement 
D)  form indicator movement 
E)  none of the above

Question 4

A centerline of a part can be a datum.

Accepted Answer

A) True 
 B)False

Question 5

When drawing a feature control frame for circularity, 0.06 is the notation if there was a 0.06 diameter tolerance zone.

Accepted Answer

A) True 
 B)False

Question 6

________________ is a boundary that takes into consideration the combined effect of feature size at MMC and geometric tolerance.

Accepted Answer

The answer of ________________ is a boundary that takes into...

Question 7

Profile tolerances are always equally disposed bilateral unless otherwise specified.

Accepted Answer

A) True 
 B)False

Question 8

In what ways do surface datum feature symbol applications, axis datum symbol applications, and center plane datum symbol applications differ from each other?

Accepted Answer

A)  When surface datums are shown on extension lines, they are offset from the dimension line arrows, while axis datums and center plane datums can align with dimension line arrowhead. 
B)  In surface datum symbols the equilateral triangle is filled, while in axis datums and center plane datums the equilateral triangle is left unfilled. 
C)  Axis datums and center plane datums are verified from one of the existing surfaces. 
D)  The surface datum is the only one to position the part in relation to a datum reference frame. 
E)  none of the above 
A)  When surface datums are shown on extension lines, they are offset from the dimension line arrows, while axis datums and center plane datums can align with dimension line arrowhead. 
B)  In surface datum symbols the equilateral triangle is filled, while in axis datums and center plane datums the equilateral triangle is left unfilled. 
C)  Axis datums and center plane datums are verified from one of the existing surfaces. 
D)  The surface datum is the only one to position the part in relation to a datum reference frame. 
E)  none of the above

Question 9

Virtual condition is one of the conditions in which a feature size can be outside of MMC.

Accepted Answer

A) True 
 B)False

Question 10

When a datum feature symbol and a feature control frame are combined, ____.

Accepted Answer

A)  the datum feature symbol is shown at the right end of the feature control frame 
B)  the datum feature symbol is shown at the base of the feature control frame 
C)  the datum feature symbol is shown at the left end of the feature control frame 
D)  the datum feature symbol is shown at the center of the top of the feature control frame 
E)  none of the above 
A)  the datum feature symbol is shown at the right end of the feature control frame 
B)  the datum feature symbol is shown at the base of the feature control frame 
C)  the datum feature symbol is shown at the left end of the feature control frame 
D)  the datum feature symbol is shown at the center of the top of the feature control frame 
E)  none of the above

Question 11

This is the smallest size that can be contracted about an external feature or the largest size that can be expanded within an internal feature.

Accepted Answer

Actual mat

Question 12

If a part feature is produced at MMC, it is considered to be at perfect form.

Accepted Answer

A) True 
 B)False

Question 13

A movable datum target symbol is used to indicate that the datum target is not fixed at its basic location and is free to translate.

Accepted Answer

A) True 
 B)False

Question 14

The term circular or line element is used to refer to ____.

Accepted Answer

A)  cross sectional tolerance zone 
B)  single line tolerance zone 
C)  entire surface tolerance zone 
D)  both a and b 
E)  all of the above 
A)  cross sectional tolerance zone 
B)  single line tolerance zone 
C)  entire surface tolerance zone 
D)  both a and b 
E)  all of the above

Question 15

The symbol for profile tolerance of a surface is an arc the height of the lettering.

Accepted Answer

A) True 
 B)False

Question 16

Circular runout provides control of single circular elements of a surface and controls circularity and the relationship of the common axes (coaxial) of parts.

Accepted Answer

A) True 
 B)False

Question 17

Where applied to surfaces constructed around a datum axis, total runout out is used to control cumulative variations of ____.

Accepted Answer

A)  coaxiality 
B)  circularity 
C)  profile of a surface 
D)  both a and c 
E)  all of the above 
A)  coaxiality 
B)  circularity 
C)  profile of a surface 
D)  both a and c 
E)  all of the above

Question 18

Which of the following is not a type of geometric tolerance?

Accepted Answer

A)  straightness 
B)  runout 
C)  location 
D)  form 
E)  none of the above 
A)  straightness 
B)  runout 
C)  location 
D)  form 
E)  none of the above

Question 19

This is a point, axis, line, or plane consistent with or resulting from processing or inspection equipment, such as a surface plate, inspection table, gage surface, or a mandrel.

Accepted Answer

The answer of This is a point, axis, line, or...

Question 20

The material condition modifying elements are ____.

Accepted Answer

A)  MMC 
B)  EECS 
C)  RFS 
D)  JKS 
E)  both a and c 
A)  MMC 
B)  EECS 
C)  RFS 
D)  JKS 
E)  both a and c

True position is the theoretically exact location ____ of a feature.

All three material condition modifying elements have specific symbols associated with them.

"FIM" is an acronym for ____.

A centerline of a part can be a datum.

When drawing a feature control frame for circularity, 0.06 is the notation if there was a 0.06 diameter tolerance zone.

________________ is a boundary that takes into consideration the combined effect of feature size at MMC and geometric tolerance.

Profile tolerances are always equally disposed bilateral unless otherwise specified.

In what ways do surface datum feature symbol applications, axis datum symbol applications, and center plane datum symbol applications differ from each other?

Virtual condition is one of the conditions in which a feature size can be outside of MMC.

When a datum feature symbol and a feature control frame are combined, ____.

This is the smallest size that can be contracted about an external feature or the largest size that can be expanded within an internal feature.

If a part feature is produced at MMC, it is considered to be at perfect form.

A movable datum target symbol is used to indicate that the datum target is not fixed at its basic location and is free to translate.

The term circular or line element is used to refer to ____.

The symbol for profile tolerance of a surface is an arc the height of the lettering.

Circular runout provides control of single circular elements of a surface and controls circularity and the relationship of the common axes (coaxial) of parts.

Where applied to surfaces constructed around a datum axis, total runout out is used to control cumulative variations of ____.

Which of the following is not a type of geometric tolerance?

This is a point, axis, line, or plane consistent with or resulting from processing or inspection equipment, such as a surface plate, inspection table, gage surface, or a mandrel.

The material condition modifying elements are ____.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Reading Electrical Diagrams and Schematics

Filters

Exam 11: Reading Geometric Dimensioning and Tolerancing

True position is the theoretically exact location ____ of a feature.

All three material condition modifying elements have specific symbols associated with them.

"FIM" is an acronym for ____.

A centerline of a part can be a datum.

When drawing a feature control frame for circularity, 0.06 is the notation if there was a 0.06 diameter tolerance zone.

________________ is a boundary that takes into consideration the combined effect of feature size at MMC and geometric tolerance.

Profile tolerances are always equally disposed bilateral unless otherwise specified.

In what ways do surface datum feature symbol applications, axis datum symbol applications, and center plane datum symbol applications differ from each other?

Virtual condition is one of the conditions in which a feature size can be outside of MMC.

When a datum feature symbol and a feature control frame are combined, ____.

This is the smallest size that can be contracted about an external feature or the largest size that can be expanded within an internal feature.

If a part feature is produced at MMC, it is considered to be at perfect form.

A movable datum target symbol is used to indicate that the datum target is not fixed at its basic location and is free to translate.

The term circular or line element is used to refer to ____.

The symbol for profile tolerance of a surface is an arc the height of the lettering.

Circular runout provides control of single circular elements of a surface and controls circularity and the relationship of the common axes (coaxial) of parts.

Where applied to surfaces constructed around a datum axis, total runout out is used to control cumulative variations of ____.

Which of the following is not a type of geometric tolerance?

This is a point, axis, line, or plane consistent with or resulting from processing or inspection equipment, such as a surface plate, inspection table, gage surface, or a mandrel.

The material condition modifying elements are ____.

Introduction to Engineering and Manufacturing Technology Print Reading

Communicating with a Sketch

Scales and Precision Measurement

Reading Lines and Lettering on a Print

Reading Multiviews

Reading Auxiliary Views

Manufacturing Materials and Processes

Reading Dimensions

Reading Prints With Fasteners and Springs

Reading Sections, Revolutions, and Conventional Breaks

Reading Linkage, Cam, Gear, and Bearing Prints

Reading Precision Sheet Metal Prints

Reading Prints of Working Drawings

Welding Processes and Reading Welding Representations

Reading Prints of Pictorial Drawings

Reading Electrical Diagrams and Schematics

Filters