Question 1

A conservation vent is used with the following term:

Accepted Answer

A)  conserving 
B)  breathing 
C)  tank terminology 
D)  gas-blanket 
A)  conserving 
B)  breathing 
C)  tank terminology 
D)  gas-blanket B

Question 2

What two types of blinds do we use?

Accepted Answer

A)  paddle and figure eight 
B)  solid and wedge 
C)  flat and plate 
D)  orifice and paddle 
A)  paddle and figure eight 
B)  solid and wedge 
C)  flat and plate 
D)  orifice and paddle A

Question 3

List the important facts associated with pipe size and diameter.

Accepted Answer

A)  most pipe used in plants is: 1/2", 3/4", 1", 1 1/2", 2", 3", 4", 6", 8", 10", 12", and 14" and higher. 
B)  the term schedule (40 or 80) refers to the actual thickness of the pipe wall. 
C)  the inside and outside diameter of a pipe is slightly different. 
D)  all of the above 
A)  most pipe used in plants is: 1/2", 3/4", 1", 1 1/2", 2", 3", 4", 6", 8", 10", 12", and 14" and higher. 
B)  the term schedule (40 or 80) refers to the actual thickness of the pipe wall. 
C)  the inside and outside diameter of a pipe is slightly different. 
D)  all of the above D

Question 4

Common storage designs include all the following except:.

Accepted Answer

A)  spheres 
B)  spheroids 
C)  cylindrical tanks 
D)  columns & towers 
A)  spheres 
B)  spheroids 
C)  cylindrical tanks 
D)  columns & towers

Question 5

Bonding is achieved by:

Accepted Answer

A)  connecting an object to the earth with a rod 
B)  physically connecting two objects together with a copper wire. 
C)  allowing electric sparks to discharge 
D)  adhering objects together with a chemical 
A)  connecting an object to the earth with a rod 
B)  physically connecting two objects together with a copper wire. 
C)  allowing electric sparks to discharge 
D)  adhering objects together with a chemical

Question 6

If a tank is rated as a 5,000 bbl tank it can safely store:

Accepted Answer

A)  160,000 gallons 
B)  230,000 gallons 
C)  210,000 gallons 
D)  275,000 gallon 
A)  160,000 gallons 
B)  230,000 gallons 
C)  210,000 gallons 
D)  275,000 gallon

Question 7

What type of shut off does a paddle blind provide?

Accepted Answer

A)  partial shut-off 
B)  double-block and bleed 
C)  positive shut-off 
D)  figure eight closure 
A)  partial shut-off 
B)  double-block and bleed 
C)  positive shut-off 
D)  figure eight closure

Question 8

Tanks, drums, and vessels are typically classified as:

Accepted Answer

A)  low and high pressure 
B)  liquid and gas service 
C)  insulated, steam traced, and water cooled. 
D)  all the above 
A)  low and high pressure 
B)  liquid and gas service 
C)  insulated, steam traced, and water cooled. 
D)  all the above

Question 9

All of the following are examples of floating roof tanks except:.

Accepted Answer

A)  pan type 
B)  pontoon type 
C)  atmospheric membrane 
D)  double deck 
A)  pan type 
B)  pontoon type 
C)  atmospheric membrane 
D)  double deck

Question 10

Process technicians use ______________ to calculate the volume in a tank:.

Accepted Answer

A)  tankage 
B)  volume tables 
C)  load cells 
D)  strapping tables 
A)  tankage 
B)  volume tables 
C)  load cells 
D)  strapping tables

Question 11

What metal is used for extremely low temperatures (below - 150˚F)?

Accepted Answer

A)  carbon steel 
B)  Type 304 stainless steel 
C)  brass 
D)  a & c 
A)  carbon steel 
B)  Type 304 stainless steel 
C)  brass 
D)  a & c

Question 12

Gas-blanketed tanks are used to:.

Accepted Answer

A)  store hazardous feedstocks 
B)  reduce air, reduce flammability and explosive range of vapors 
C)  cool-off product by holding molecules closer to the liquid 
D)  A & B 
A)  store hazardous feedstocks 
B)  reduce air, reduce flammability and explosive range of vapors 
C)  cool-off product by holding molecules closer to the liquid 
D)  A & B

Question 13

What metal would you use for a vessel containing non-corrosive material at 100 psig and 300˚F?

Accepted Answer

A)  carbon steel 
B)  hasteloy 
C)  stainless steel 
D)  nonferrous alloy 
A)  carbon steel 
B)  hasteloy 
C)  stainless steel 
D)  nonferrous alloy

Question 14

The welded joint on a cone-roof where the roof joins the shell is :.

Accepted Answer

A)  engineered stronger due to higher vapor pressures near the top 
B)  purposely made weaker than other joints so that it will burst and relieve pressure and not spill contents. 
C)  helps confine the fluid should a fire or explosion occur inside a tank. 
D)  B & C 
A)  engineered stronger due to higher vapor pressures near the top 
B)  purposely made weaker than other joints so that it will burst and relieve pressure and not spill contents. 
C)  helps confine the fluid should a fire or explosion occur inside a tank. 
D)  B & C

Question 15

Water draws are provided at:

Accepted Answer

A)  the top 
B)  the middle 
C)  the bottom 
D)  are not provided in hydrocarbon systems 
A)  the top 
B)  the middle 
C)  the bottom 
D)  are not provided in hydrocarbon systems

Question 16

Select the various inspection procedures used in a process plant.

Accepted Answer

A)  visual, electronic-sonic, x-ray, magnetic 
B)  f-max, post hoc, biserial correlation inspection 
C)  standard deviation, time chart inspection 
D)  spearman rank correlation, magnetic particle inspection 
A)  visual, electronic-sonic, x-ray, magnetic 
B)  f-max, post hoc, biserial correlation inspection 
C)  standard deviation, time chart inspection 
D)  spearman rank correlation, magnetic particle inspection

Question 17

What information do process technicians find on vessel design sheets?

Accepted Answer

A)  total cost of equipment 
B)  the factors entering into the selection, use, and need for periodic inspection of materials used to make vessels. 
C)  the factors or variables of each process and system 
D)  manufacturer code stamp listings 
A)  total cost of equipment 
B)  the factors entering into the selection, use, and need for periodic inspection of materials used to make vessels. 
C)  the factors or variables of each process and system 
D)  manufacturer code stamp listings

Question 18

Spherical and spheroidal storage tanks are designed to store gases or pressures above:

Accepted Answer

A)  1 psig 
B)  3 psi 
C)  above 5 psig 
D)  below 5 psig 
A)  1 psig 
B)  3 psi 
C)  above 5 psig 
D)  below 5 psig

Question 19

The threads on screwed piping is treated with _______ before joining.

Accepted Answer

A)  Teflon tape 
B)  Thread compound 
C)  combination of Teflon and thread compound 
D)  all the above 
A)  Teflon tape 
B)  Thread compound 
C)  combination of Teflon and thread compound 
D)  all the above

Question 20

A 55-gallon barrel typically holds:.

Accepted Answer

A)  42 gallons 
B)  46 gallons 
C)  50 gallons 
D)  55 gallons 
A)  42 gallons 
B)  46 gallons 
C)  50 gallons 
D)  55 gallons

A conservation vent is used with the following term:

What two types of blinds do we use?

List the important facts associated with pipe size and diameter.

Common storage designs include all the following except:.

Bonding is achieved by:

If a tank is rated as a 5,000 bbl tank it can safely store:

What type of shut off does a paddle blind provide?

Tanks, drums, and vessels are typically classified as:

All of the following are examples of floating roof tanks except:.

Process technicians use ______________ to calculate the volume in a tank:.

What metal is used for extremely low temperatures (below - 150˚F)?

Gas-blanketed tanks are used to:.

What metal would you use for a vessel containing non-corrosive material at 100 psig and 300˚F?

The welded joint on a cone-roof where the roof joins the shell is :.

Water draws are provided at:

Select the various inspection procedures used in a process plant.

What information do process technicians find on vessel design sheets?

Spherical and spheroidal storage tanks are designed to store gases or pressures above:

The threads on screwed piping is treated with _______ before joining.

A 55-gallon barrel typically holds:.

Introduction to Process Equipment

Valves

Pumps

Compressors

Turbines and Motors

Heat Exchangers

Cooling Towers

Steam Generation- Boilers

Fired Heaters Furnaces

Instruments

Process Diagrams

Utility Systems

Reaction Systems

Distillation Systems

Extraction and Other Separation Systems

Plastics Systems

Filters

Exam 3: Piping and Vessels

A conservation vent is used with the following term:

What two types of blinds do we use?

List the important facts associated with pipe size and diameter.

Common storage designs include all the following except:.

Bonding is achieved by:

If a tank is rated as a 5,000 bbl tank it can safely store:

What type of shut off does a paddle blind provide?

Tanks, drums, and vessels are typically classified as:

All of the following are examples of floating roof tanks except:.

Process technicians use ______________ to calculate the volume in a tank:.

What metal is used for extremely low temperatures (below - 150˚F)?

Gas-blanketed tanks are used to:.

What metal would you use for a vessel containing non-corrosive material at 100 psig and 300˚F?

The welded joint on a cone-roof where the roof joins the shell is :.

Water draws are provided at:

Select the various inspection procedures used in a process plant.

What information do process technicians find on vessel design sheets?

Spherical and spheroidal storage tanks are designed to store gases or pressures above:

The threads on screwed piping is treated with _______ before joining.

A 55-gallon barrel typically holds:.

Introduction to Process Equipment

Valves

Pumps

Compressors

Turbines and Motors

Heat Exchangers

Cooling Towers

Steam Generation- Boilers

Fired Heaters Furnaces

Instruments

Process Diagrams

Utility Systems

Reaction Systems

Distillation Systems

Extraction and Other Separation Systems

Plastics Systems

Filters