Question 1

The function of a transducer is

Accepted Answer

A) To decodify the input signal 
B) To convert the primary signal into a more useful quantity usually an electrical impulse 
C) To amplify the input signal 
D) To codify the input signal 
E) To modify the input signal 
A) To decodify the input signal 
B) To convert the primary signal into a more useful quantity usually an electrical impulse 
C) To amplify the input signal 
D) To codify the input signal 
E) To modify the input signal B

Question 2

A tool has tool signature 15, 15, 10, 10, 15, 10, (3 mm). Which of the following angle is not of 15°?

Accepted Answer

A) Cutting edge angle 
B) Parting off 
C) Side rake angle 
D) End relief angle 
E) Back rake angle 
A) Cutting edge angle 
B) Parting off 
C) Side rake angle 
D) End relief angle 
E) Back rake angle D

Question 3

Flange wrinkling is a defect associated with

Accepted Answer

A) Cold heating 
B) Cold rolling 
C) Deep drawing 
D) Die casting 
E) None of the above 
A) Cold heating 
B) Cold rolling 
C) Deep drawing 
D) Die casting 
E) None of the above C

Question 4

Which of the following is relatively a low temperature brazing process?

Accepted Answer

A) Brass brazing 
B) Silver manganese brazing 
C) Copper brazing 
D) Nickel chrome brazing 
E) Silver brazing 
A) Brass brazing 
B) Silver manganese brazing 
C) Copper brazing 
D) Nickel chrome brazing 
E) Silver brazing

Question 5

Die casted gears are generally used in

Accepted Answer

A) Counters 
B) Toys 
C) Cameras 
D) Any of the above 
E) None of the above 
A) Counters 
B) Toys 
C) Cameras 
D) Any of the above 
E) None of the above

Question 6

Post cleaning is done in case of brazed joints to

Accepted Answer

A) Prevent corrosion 
B) Remove scale 
C) Strengthen the joint 
D) Increase the strength of the joint 
E) All of the above 
A) Prevent corrosion 
B) Remove scale 
C) Strengthen the joint 
D) Increase the strength of the joint 
E) All of the above

Question 7

Which property of sand is measured by a dilatometer?

Accepted Answer

A) Clay content 
B) Permeability 
C) Hot strength 
D) Fineness 
E) Moisture content 
A) Clay content 
B) Permeability 
C) Hot strength 
D) Fineness 
E) Moisture content

Question 8

Core prints are

Accepted Answer

A) Impressions left on cores during core making 
B) Hard surfaces on cores mainly meant for resisting deformation 
C) Blue prints for core manufacturing 
D) Holes or recesses in core meant for locating cores in position 
E) None of the above 
A) Impressions left on cores during core making 
B) Hard surfaces on cores mainly meant for resisting deformation 
C) Blue prints for core manufacturing 
D) Holes or recesses in core meant for locating cores in position 
E) None of the above

Question 9

Which of the following is not a squeezing process?

Accepted Answer

A) Riveting 
B) Thread rolling 
C) Coining 
D) Trimming 
E) Knurling 
A) Riveting 
B) Thread rolling 
C) Coining 
D) Trimming 
E) Knurling

Question 10

Which of the following chucking device can be used on lathe?

Accepted Answer

A) Dog carrier 
B) Face plate 
C) Collets 
D) Mandrel 
E) All of the above 
A) Dog carrier 
B) Face plate 
C) Collets 
D) Mandrel 
E) All of the above

Question 11

Honing is used to

Accepted Answer

A) correct ovality 
B) waviness of axis 
C) non-parallelism of cylindrical features 
D) All of the above 
E) Parting off 
A) correct ovality 
B) waviness of axis 
C) non-parallelism of cylindrical features 
D) All of the above 
E) Parting off

Question 12

Which one of the following is not a angle measuring device?

Accepted Answer

A) Angle iron 
B) Angle gauge blocks 
C) Combination square 
D) Bevel protector 
E) Signal bar 
A) Angle iron 
B) Angle gauge blocks 
C) Combination square 
D) Bevel protector 
E) Signal bar

Question 13

A thin tube is to be cut by hacksawing. Blades with following TPI are available which blade will be appropriate for the job

Accepted Answer

A) 14 TPI 
B) 4- TPI 
C) 18 TPI 
D) 32 TPI 
E) 20 TPI 
A) 14 TPI 
B) 4- TPI 
C) 18 TPI 
D) 32 TPI 
E) 20 TPI

Question 14

The process of increasing the cross-section of a job with a reduction in its length is termed

Accepted Answer

A) Upsetting 
B) Parting off 
C) Drawing out 
D) Cutting 
A) Upsetting 
B) Parting off 
C) Drawing out 
D) Cutting

Question 15

While grinding the increase in wheel speed, with constant feed rate, results in

Accepted Answer

A) glazing of wheel 
B) reduction of the chip size 
C) Parting off 
D) abrasive marks on work piece 
E) shining surface 
A) glazing of wheel 
B) reduction of the chip size 
C) Parting off 
D) abrasive marks on work piece 
E) shining surface

Question 16

Low helix drills are used for machining

Accepted Answer

A) Brass 
B) bronze 
C) bakelite 
D) Any of the above 
E) Parting off 
A) Brass 
B) bronze 
C) bakelite 
D) Any of the above 
E) Parting off

Question 17

Unequal lengths of lips of a twist drill are likely to result in

Accepted Answer

A) Smooth surface 
B) Low power consumption 
C) Low heat generation 
D) Elliptical hole 
E) Oversize hole 
A) Smooth surface 
B) Low power consumption 
C) Low heat generation 
D) Elliptical hole 
E) Oversize hole

Question 18

Accuracy is

Accepted Answer

A) The repeatability of a measuring process 
B) Error of judgment in recording an observation 
C) The ability of an instrument to reproduce same reading under identical situations 
D) Agreement of the result of a measurement with the true value of the measured quantity 
E) None of the above 
A) The repeatability of a measuring process 
B) Error of judgment in recording an observation 
C) The ability of an instrument to reproduce same reading under identical situations 
D) Agreement of the result of a measurement with the true value of the measured quantity 
E) None of the above

Question 19

For resistance welding

Accepted Answer

A) Voltage is low and current is high 
B) Voltage is high and current is low 
C) Both voltage and current are high 
D) Both voltage and current are low 
E) None of the above 
A) Voltage is low and current is high 
B) Voltage is high and current is low 
C) Both voltage and current are high 
D) Both voltage and current are low 
E) None of the above

Question 20

In a Brinell hardness test the hardness number is determined by the measurement of

Accepted Answer

A) Width of depression 
B) Depth of depression 
C) Diameter of depression 
D) Surface area of depression 
E) None of the above 
A) Width of depression 
B) Depth of depression 
C) Diameter of depression 
D) Surface area of depression 
E) None of the above

The function of a transducer is

A tool has tool signature 15, 15, 10, 10, 15, 10, (3 mm). Which of the following angle is not of 15°?

Flange wrinkling is a defect associated with

Which of the following is relatively a low temperature brazing process?

Die casted gears are generally used in

Post cleaning is done in case of brazed joints to

Which property of sand is measured by a dilatometer?

Core prints are

Which of the following is not a squeezing process?

Which of the following chucking device can be used on lathe?

Honing is used to

Which one of the following is not a angle measuring device?

A thin tube is to be cut by hacksawing. Blades with following TPI are available which blade will be appropriate for the job

The process of increasing the cross-section of a job with a reduction in its length is termed

While grinding the increase in wheel speed, with constant feed rate, results in

Low helix drills are used for machining

Unequal lengths of lips of a twist drill are likely to result in

Accuracy is

For resistance welding

In a Brinell hardness test the hardness number is determined by the measurement of

Manufacturing Processes and Materials and Tools

Mechanical Engineering and Manufacturing Processes

Mechanical Engineering: Casting, Machining, and Welding

Mechanical Engineering Processes and Concepts

Manufacturing and Welding Processes

Manufacturing and Machining Techniques

Mechanical Engineering: Foundry, Machining, and Materials

Metal Cleaning, Abrasives, and Machining Techniques

Manufacturing and Materials Engineering

Technical Manufacturing and Engineering

Manufacturing Processes: Wood Moisture, Alloyed Cast Iron, Cutting Tools, Welding

Techniques for Hardness Testing, Drilling, Machining, Welding, and Casting

Machining Processes, Techniques and Tools

Filters

Exam 3: Industrial Engineering and Manufacturing Processes and Materials

The function of a transducer is

A tool has tool signature 15, 15, 10, 10, 15, 10, (3 mm). Which of the following angle is not of 15°?

Flange wrinkling is a defect associated with

Which of the following is relatively a low temperature brazing process?

Die casted gears are generally used in

Post cleaning is done in case of brazed joints to

Which property of sand is measured by a dilatometer?

Core prints are

Which of the following is not a squeezing process?

Which of the following chucking device can be used on lathe?

Honing is used to

Which one of the following is not a angle measuring device?

A thin tube is to be cut by hacksawing. Blades with following TPI are available which blade will be appropriate for the job

The process of increasing the cross-section of a job with a reduction in its length is termed

While grinding the increase in wheel speed, with constant feed rate, results in

Low helix drills are used for machining

Unequal lengths of lips of a twist drill are likely to result in

Accuracy is

For resistance welding

In a Brinell hardness test the hardness number is determined by the measurement of

Manufacturing Processes and Materials and Tools

Mechanical Engineering and Manufacturing Processes

Mechanical Engineering: Casting, Machining, and Welding

Mechanical Engineering Processes and Concepts

Manufacturing and Welding Processes

Manufacturing and Machining Techniques

Mechanical Engineering: Foundry, Machining, and Materials

Metal Cleaning, Abrasives, and Machining Techniques

Manufacturing and Materials Engineering

Technical Manufacturing and Engineering

Manufacturing Processes: Wood Moisture, Alloyed Cast Iron, Cutting Tools, Welding

Techniques for Hardness Testing, Drilling, Machining, Welding, and Casting

Machining Processes, Techniques and Tools

Filters