Question 1

3D DESIGN
-2D outline constructed using the line and circle tools can be extruded to form a 3D model

Accepted Answer

A) Yes 
B) No 
C) Only if it is first made into a region 
D) Either if it is first made into a region or if its outline is edited to form a closed polyline 
A) Yes 
B) No 
C) Only if it is first made into a region 
D) Either if it is first made into a region or if its outline is edited to form a closed polyline

Question 2

3D DESIGN
-Which gives the best rendering results

Accepted Answer

A)  Medium 
B)  High 
C)  Presentation 
D)  They are all as good as each other 
A)  Medium 
B)  High 
C)  Presentation 
D)  They are all as good as each other

Question 3

2D DESIGN
-A tooltip is

Accepted Answer

A)  A description of the tool's use appearing in a rectangle when the cursor is placed on a tool icon 
B)  The name given to a tool 
C)  The instruction which appears at the left-hand end of the status bar when a tool is chosen 
D)  A tip which can be read from the Help screen for a tool 
A)  A description of the tool's use appearing in a rectangle when the cursor is placed on a tool icon 
B)  The name given to a tool 
C)  The instruction which appears at the left-hand end of the status bar when a tool is chosen 
D)  A tip which can be read from the Help screen for a tool

Question 4

2D DESIGN
-When using the Stretch tool

Accepted Answer

A)  Circles can be stretched into ellipses 
B)  The tool has no effect upon circles 
C)  Be careful because circles can be erased 
D)  Treat circles like any other part of the drawing being stretched 
A)  Circles can be stretched into ellipses 
B)  The tool has no effect upon circles 
C)  Be careful because circles can be erased 
D)  Treat circles like any other part of the drawing being stretched

Question 5

3D DESIGN
-When calling the Extrude tool the following abbreviation can be entered at the command line

Accepted Answer

A)  ex 
B)  extr 
C)  There is no abbreviation. The name extrude must be entered in full 
D)  ext 
A)  ex 
B)  extr 
C)  There is no abbreviation. The name extrude must be entered in full 
D)  ext

Question 6

3D DESIGN
-Before viewing positions can be set from the Viewpoint Presets dialog the set variable UCSFOLLOW must first be set

Accepted Answer

A)  On 
B)  Off 
C)  To the figure of 2 
D)  It does not matter whether it is set on or off 
A)  On 
B)  Off 
C)  To the figure of 2 
D)  It does not matter whether it is set on or off

Question 7

2D DESIGN
-The Ribbon can be closed by entering the following at the command line

Accepted Answer

A)  openribbon 
B)  ribbonclose 
C)  ribbonon 
D)  fullribbon 
A)  openribbon 
B)  ribbonclose 
C)  ribbonon 
D)  fullribbon

Question 8

3D DESIGN
-A drawing can only be printed or plotted from a Paper Space drawing

Accepted Answer

A)  This is correct 
B)  Yes - providing the MODEL button has been clicked 
C)  Drawings can be printed or plotted from either Model Space or Paper Space 
D)  Drawings can only be printed from Paper Space, but plotted only from Model Space 
A)  This is correct 
B)  Yes - providing the MODEL button has been clicked 
C)  Drawings can be printed or plotted from either Model Space or Paper Space 
D)  Drawings can only be printed from Paper Space, but plotted only from Model Space

Question 9

2D DESIGN
-When a layer is turned off

Accepted Answer

A)  File space is saved when saving the file 
B)  It makes no real difference. Details can still be added to the layer 
C)  Details cannot be erased from the layer 
D)  Details on the layer cannot be seen 
A)  File space is saved when saving the file 
B)  It makes no real difference. Details can still be added to the layer 
C)  Details cannot be erased from the layer 
D)  Details on the layer cannot be seen

Question 10

2D DESIGN
-Which of the following statement is correct

Accepted Answer

A)  The Purge tool can be used only when inserting blocks 
B)  The Purge tool can be used only to delete unwanted detail from any drawing 
C)  The Purge tool can be used only for deleting exploded blocks from drawings 
D)  The Purge tool can be called only by entering purge at the command line 
A)  The Purge tool can be used only when inserting blocks 
B)  The Purge tool can be used only to delete unwanted detail from any drawing 
C)  The Purge tool can be used only for deleting exploded blocks from drawings 
D)  The Purge tool can be called only by entering purge at the command line

Question 11

3D DESIGN
-When constructing 3D model drawings in multiple viewports

Accepted Answer

A)  The set variable UCSFOLLOW must be set to on 
B)  The set variable UCSFOLLOW must be set to off 
C)  It does not matter whether the set variable UCSFOLLOW is set on or off 
D)  The set variable UCSFOLLOW must be set to 3 
A)  The set variable UCSFOLLOW must be set to on 
B)  The set variable UCSFOLLOW must be set to off 
C)  It does not matter whether the set variable UCSFOLLOW is set on or off 
D)  The set variable UCSFOLLOW must be set to 3

Question 12

2D DESIGN
-The term dragging means

Accepted Answer

A)  Left-click on an item and the item can be moved to another position on screen 
B)  Double-click on an item. The item can then be moved to another point on screen 
C)  Holding down the left-hand button of the mouse on an item and moving it to another point on screen 
D)  Press the right-hand button of the mouse. This allows an item to be moved anywhere on screen 
A)  Left-click on an item and the item can be moved to another position on screen 
B)  Double-click on an item. The item can then be moved to another point on screen 
C)  Holding down the left-hand button of the mouse on an item and moving it to another point on screen 
D)  Press the right-hand button of the mouse. This allows an item to be moved anywhere on screen

Question 13

3D DESIGN
-Before the UCS system can be used, the UCS icon

Accepted Answer

A)  The UCS icon can only show on screen if the setting of the set variable UCSFOLLOW is correct 
B)  Must be showing somewhere on screen 
C)  Need not appear anywhere on screen 
D)  Must be showing at the bottom left-hand corner of the screen 
A)  The UCS icon can only show on screen if the setting of the set variable UCSFOLLOW is correct 
B)  Must be showing somewhere on screen 
C)  Need not appear anywhere on screen 
D)  Must be showing at the bottom left-hand corner of the screen

Question 14

2D DESIGN
-The set variable PELLIPSE can be set to either 0 or 1 when it allows the following actions

Accepted Answer

A)  When set to 0 the Edit Polyline tool to be used on ellipses 
B)  When set to 1 the Edit Polyline tool to be used on ellipses 
C)  When set to 0 it allows ellipses to be drawn with the major axis at any angle 
D)  When set to 0 ellipses become polylines. 
A)  When set to 0 the Edit Polyline tool to be used on ellipses 
B)  When set to 1 the Edit Polyline tool to be used on ellipses 
C)  When set to 0 it allows ellipses to be drawn with the major axis at any angle 
D)  When set to 0 ellipses become polylines.

Question 15

2D DESIGN
-The Arc tool can be called from

Accepted Answer

A)  The Home/Modify panel 
B)  The Home/Draw panel 
C)  The Parametric/Geometric panel 
D)  The tool cannot be called from the ribbon 
A)  The Home/Modify panel 
B)  The Home/Draw panel 
C)  The Parametric/Geometric panel 
D)  The tool cannot be called from the ribbon

Question 16

2D DESIGN
-If a layer is locked

Accepted Answer

A)  Details can be added to a locked layer 
B)  Details can be erased from a locked layer 
C)  Details cannot be added or erased from a locked layer 
D)  can be added to a locked layer but they disappear when the drawing file is saved 
A)  Details can be added to a locked layer 
B)  Details can be erased from a locked layer 
C)  Details cannot be added or erased from a locked layer 
D)  can be added to a locked layer but they disappear when the drawing file is saved

Question 17

3D DESIGN
-When using the Section tool on a 3D solid model drawing

Accepted Answer

A)  Hatching of the resulting sectional view is automatic 
B)  The section outline must be removed from the 3D solid model drawing 
C)  Only a sectional view outline is formed 
D)  The resulting sectional view automatically appears as a separate view in the drawing area 
A)  Hatching of the resulting sectional view is automatic 
B)  The section outline must be removed from the 3D solid model drawing 
C)  Only a sectional view outline is formed 
D)  The resulting sectional view automatically appears as a separate view in the drawing area

Question 18

3D DESIGN
-Can the Union tool be used to form 3D solid drawings from a number of objects constructed using any of the 3D Objects tools Box, Sphere, Cylinder, Cone, Torus and Wedge

Accepted Answer

A)  Yes 
B)  Yes. 
C)  Only from the Box and Cone tools 
D)  Yes, but not from the Torus tool 
A)  Yes 
B)  Yes. 
C)  Only from the Box and Cone tools 
D)  Yes, but not from the Torus tool

Question 19

3D DESIGN
-The Solprof tool is used for the following purpose

Accepted Answer

A)  To produce a profile for a 3D solid model drawing in a database 
B)  To produce an outline-only drawing from a 3D solid model drawing 
C)  To provide a profile similar to a front view from a 3D solid model drawing 
D)  To change a 3D solid model drawing from a Model Space drawing to a Paper Space drawing 
A)  To produce a profile for a 3D solid model drawing in a database 
B)  To produce an outline-only drawing from a 3D solid model drawing 
C)  To provide a profile similar to a front view from a 3D solid model drawing 
D)  To change a 3D solid model drawing from a Model Space drawing to a Paper Space drawing

Question 20

2D DESIGN
-Associative hatching is a term given to

Accepted Answer

A)  Types of hatching which can be joined together 
B)  Hatching which is associated with the colour of the area being hatched 
C)  Hatching which is associated with objects which are moved within a hatched area 
D)  Hatching which is associated with a hatched area from another part of a drawing 
A)  Types of hatching which can be joined together 
B)  Hatching which is associated with the colour of the area being hatched 
C)  Hatching which is associated with objects which are moved within a hatched area 
D)  Hatching which is associated with a hatched area from another part of a drawing

Exam 1: Autocad 2013 2D and 3D Design

3D DESIGN -2D outline constructed using the line and circle tools can be extruded to form a 3D model

3D DESIGN -Which gives the best rendering results

2D DESIGN -A tooltip is

2D DESIGN -When using the Stretch tool

3D DESIGN -When calling the Extrude tool the following abbreviation can be entered at the command line

3D DESIGN -Before viewing positions can be set from the Viewpoint Presets dialog the set variable UCSFOLLOW must first be set

2D DESIGN -The Ribbon can be closed by entering the following at the command line

3D DESIGN -A drawing can only be printed or plotted from a Paper Space drawing

2D DESIGN -When a layer is turned off

2D DESIGN -Which of the following statement is correct

3D DESIGN -When constructing 3D model drawings in multiple viewports

2D DESIGN -The term dragging means

3D DESIGN -Before the UCS system can be used, the UCS icon

2D DESIGN -The set variable PELLIPSE can be set to either 0 or 1 when it allows the following actions

2D DESIGN -The Arc tool can be called from

2D DESIGN -If a layer is locked

3D DESIGN -When using the Section tool on a 3D solid model drawing

3D DESIGN -Can the Union tool be used to form 3D solid drawings from a number of objects constructed using any of the 3D Objects tools Box, Sphere, Cylinder, Cone, Torus and Wedge

3D DESIGN -The Solprof tool is used for the following purpose

2D DESIGN -Associative hatching is a term given to

Filters