Question 1

How many Arista switches may be a part of a single MLAG domain?

Accepted Answer

A)  2 
B)  4 
C)  8 
D)  16 
A)  2 
B)  4 
C)  8 
D)  16

Question 2

Arista MLAG uses which of the following protocols for inter-switch communication?

Accepted Answer

A)  BGP 
B)  IEEE 1588 
C)  STP 
D)  None of the above 
A)  BGP 
B)  IEEE 1588 
C)  STP 
D)  None of the above

Question 3

What must be active on the VMware side in order for EOS to have visibility into vNIC counters?

Accepted Answer

A)  vSwitches must be used. 
B)  Distributed switches must be used. 
C)  vSphere must be used. 
D)  vNIC counters are not supported in VMTracer. 
A)  vSwitches must be used. 
B)  Distributed switches must be used. 
C)  vSphere must be used. 
D)  vNIC counters are not supported in VMTracer.

Question 4

Which Arista switch series supports more than eight line cards?

Accepted Answer

A)  7050 
B)  7250QX 
C)  7500 
D)  7300 
A)  7050 
B)  7250QX 
C)  7500 
D)  7300

Question 5

you should disable Spanning-Tree on the Arista MLAG peer link VLAN?

Accepted Answer

A) True 
 B)False

Question 6

What is the VXLAN equivalent to a VLAN ID?

Accepted Answer

A)  VTEP 
B)  VNI 
C)  VTP 
D)  VXLAN 
A)  VTEP 
B)  VNI 
C)  VTP 
D)  VXLAN

Question 7

Which of the following commands will show the currently running version of EOS?

Accepted Answer

A)  show version 
B)  show version detail 
C)  bash more /etc/Eos-release 
D)  all of the above 
A)  show version 
B)  show version detail 
C)  bash more /etc/Eos-release 
D)  all of the above

Question 8

Which of the following are valid commands on EOS 4.14? (Choose three.)

Accepted Answer

A) show run all B) show run diffs C) show run sanitized D) show run section A) show run all B) show run diffs C) show run sanitized D) show run section

Question 9

Given the following output, which of the following have you likely configured?

Accepted Answer

A)  Advanced Mirroring with Packet Truncation 
B)  Advanced Mirroring with ACLs 
C)  Agile Ports 
D)  Buffer Tuning 
A)  Advanced Mirroring with Packet Truncation 
B)  Advanced Mirroring with ACLs 
C)  Agile Ports 
D)  Buffer Tuning

Question 10

Which of the following Arista switch series' supports Zero Touch Provisioning (ZTP)?

Accepted Answer

A)  7050 
B)  7280E 
C)  7300 
D)  7500E 
A)  7050 
B)  7280E 
C)  7300 
D)  7500E

Question 11

On EOS 4.13.1F, which of the following statements are true in regards to Arista's Tap Aggregation feature? (Select two)

Accepted Answer

A)  Tap ports are send only. 
B)  Tap ports are receive only. 
C)  Tool ports are send only. 
D)  Tool ports are receive only. 
A)  Tap ports are send only. 
B)  Tap ports are receive only. 
C)  Tool ports are send only. 
D)  Tool ports are receive only.

Question 12

How does Arista's VMTracer feature support multi-tenancy?

Accepted Answer

A)  By allowing VMs to be run on the switch itself. 
B)  By allowing connections to multiple ESXi hosts. 
C)  By allowing connections to multiple vCenters. 
D)  VMTracer does not support multi-tenancy. 
A)  By allowing VMs to be run on the switch itself. 
B)  By allowing connections to multiple ESXi hosts. 
C)  By allowing connections to multiple vCenters. 
D)  VMTracer does not support multi-tenancy.

Question 13

What does LANZ do?

Accepted Answer

A)  LANZ reports on microbursting events at extremely small intervals of time. 
B)  LANZ alters the flow of frames based on an interfaces high and low queue-thresholds. 
C)  LANZ is a form of QoS that allows for microsecond-levels of precision on interfaces that support it. 
D)  LANZ is the means whereby late packets can be analyzed. 
A)  LANZ reports on microbursting events at extremely small intervals of time. 
B)  LANZ alters the flow of frames based on an interfaces high and low queue-thresholds. 
C)  LANZ is a form of QoS that allows for microsecond-levels of precision on interfaces that support it. 
D)  LANZ is the means whereby late packets can be analyzed.

Question 14

Which of the following schedule commands will not be accepted by the parser?

Accepted Answer

A)  schedule test interval 10 max-log-files 10 command show interface counters 
B)  schedule test interval 10 max-log-files 10 command show counters status 
C)  schedule test interval 10 max-log-files 10 command show bob's hairy eyeball 
D)  None of the above 
A)  schedule test interval 10 max-log-files 10 command show interface counters 
B)  schedule test interval 10 max-log-files 10 command show counters status 
C)  schedule test interval 10 max-log-files 10 command show bob's hairy eyeball 
D)  None of the above

Question 15

Given the following output, what can you determine about Ethernet13?

Accepted Answer

A)  Ethernet13 has a QSFP interface 
B)  Ethernet13 has a QSFP+interface 
C)  Ethernet13 is an Agile Port 
D)  Ethernet13 has a hardware error that is causing it to misreport its connection speed. 
A)  Ethernet13 has a QSFP interface 
B)  Ethernet13 has a QSFP+interface 
C)  Ethernet13 is an Agile Port 
D)  Ethernet13 has a hardware error that is causing it to misreport its connection speed.

Question 16

What is the name of the Arista EOS feature that allows you to set triggers and perform actions on those triggers?

Accepted Answer

A)  Event Manager 
B)  Event Monitor 
C)  Event Trigger 
D)  Event History 
A)  Event Manager 
B)  Event Monitor 
C)  Event Trigger 
D)  Event History

Question 17

Which of the following Tap Aggregation command sessions are correct?

Accepted Answer

A)    
B)    
C)    
D)    
A)    
B)    
C)    
D)

Question 18

VMTracer requires which of the following?

Accepted Answer

A)  Root-level access to vCenter. 
B)  Read-level access to vCenter. 
C)  Read/write-level access to vCenter. 
D)  VMTracer does not require a username on vCenter. 
A)  Root-level access to vCenter. 
B)  Read-level access to vCenter. 
C)  Read/write-level access to vCenter. 
D)  VMTracer does not require a username on vCenter.

Question 19

Which of the following Arista switches support LANZ?

Accepted Answer

A)  7010 
B)  7150 
C)  7500E 
D)  7048T 
A)  7010 
B)  7150 
C)  7500E 
D)  7048T

Question 20

With two switches in an MLAG domain, which of the following commands is a legitimate way to make interfaces on one of the peers part of mlag 43?

Accepted Answer

A)  Peer-1(config-if-Po43) #mlag 43 Peer-1(config-if-Po43) #mlag 43 
B)  Peer-1(config-if-Et43) #mlag 43 Peer-1(config-if-Et43) 
C)  Peer-1(config-if-Vl43) #mlag 43 Peer-1(config-if-Vl43) 
D)  There can only be 32 MLAGs on a switch, so MLAG 43 is impossible. 
A)  Peer-1(config-if-Po43) #mlag 43 Peer-1(config-if-Po43) #mlag 43 
B)  Peer-1(config-if-Et43) #mlag 43 Peer-1(config-if-Et43) 
C)  Peer-1(config-if-Vl43) #mlag 43 Peer-1(config-if-Vl43) 
D)  There can only be 32 MLAGs on a switch, so MLAG 43 is impossible.

How many Arista switches may be a part of a single MLAG domain?

Arista MLAG uses which of the following protocols for inter-switch communication?

What must be active on the VMware side in order for EOS to have visibility into vNIC counters?

Which Arista switch series supports more than eight line cards?

you should disable Spanning-Tree on the Arista MLAG peer link VLAN?

What is the VXLAN equivalent to a VLAN ID?

Which of the following commands will show the currently running version of EOS?

Which of the following are valid commands on EOS 4.14? (Choose three.)

Given the following output, which of the following have you likely configured?

Which of the following Arista switch series' supports Zero Touch Provisioning (ZTP)?

On EOS 4.13.1F, which of the following statements are true in regards to Arista's Tap Aggregation feature? (Select two)

How does Arista's VMTracer feature support multi-tenancy?

What does LANZ do?

Which of the following schedule commands will not be accepted by the parser?

Given the following output, what can you determine about Ethernet13?

What is the name of the Arista EOS feature that allows you to set triggers and perform actions on those triggers?

Which of the following Tap Aggregation command sessions are correct?

VMTracer requires which of the following?

Which of the following Arista switches support LANZ?

With two switches in an MLAG domain, which of the following commands is a legitimate way to make interfaces on one of the peers part of mlag 43?

Arista Linux Essentials Exam

Filters

Exam 1: Arista Certified Engineering Associate

How many Arista switches may be a part of a single MLAG domain?

Arista MLAG uses which of the following protocols for inter-switch communication?

What must be active on the VMware side in order for EOS to have visibility into vNIC counters?

Which Arista switch series supports more than eight line cards?

you should disable Spanning-Tree on the Arista MLAG peer link VLAN?

What is the VXLAN equivalent to a VLAN ID?

Which of the following commands will show the currently running version of EOS?

Which of the following are valid commands on EOS 4.14? (Choose three.)

Given the following output, which of the following have you likely configured?

Which of the following Arista switch series' supports Zero Touch Provisioning (ZTP)?

On EOS 4.13.1F, which of the following statements are true in regards to Arista's Tap Aggregation feature? (Select two)

How does Arista's VMTracer feature support multi-tenancy?

What does LANZ do?

Which of the following schedule commands will not be accepted by the parser?

Given the following output, what can you determine about Ethernet13?

What is the name of the Arista EOS feature that allows you to set triggers and perform actions on those triggers?

Which of the following Tap Aggregation command sessions are correct?

VMTracer requires which of the following?

Which of the following Arista switches support LANZ?

With two switches in an MLAG domain, which of the following commands is a legitimate way to make interfaces on one of the peers part of mlag 43?

Arista Linux Essentials Exam

Filters